Original black Lucas screw on bakelite knob, plain top. No 8 NC female thread (32 tpi, 0.164" major OD). Approx. 19mm diameter x 25mm long.
Parts
battery isolating switch with flange (53mm hole centres) for panel fixing and black know marked Off with arrow. requires 19.5mm hole and two 4mm fixing holes. two 8mm electrical cable connection...
sturdy panel mounted battery master switch, similar to Lucas SSB106 model.
requires 19mm hole in panel. well made reproduction part
requires 19mm hole in panel. well made reproduction part
battery master switch, cheaper alternative, black plastic body, red removable plastic key. usually mounted in earth lead.
Battery master switch for dashboard mounting etc., mounting flange (53mm hole centres). knob can be detached for installation by removal of rear circlip. usually mounted into earth lead.
simple yet effective battery master switch- fits on the battery post - no modifications needed -screw knob detaches if required.
brake light switch, terminals protected by a rubber cover, connects to linkage with a spring, switch 30mm long x 33mm wide x 30mm tall with fixing hole centres 24mm, spring length including hook...
as Lucas pattern 51C 'pull on' brake switch, metal body 63mm wide x 35mm deep x 40mm tall with 51mm fixing hole centres, screw terminals on top. Ford part reference Y-13480
Brake light switch which connects to linkage with a spring. Electrical contacts 'breaks' on pull. No rubber cover .
brown bakelite type body, lever arm action which makes contact when pulled. fits to RHD cars/5cwt van & LHD E83W
brown bakelite type body, lever arm action which makes contact when pulled. suits RHD E83W and LHD cars/5cwt van
battery master switch spare key for our 445 switch, dimensions - tongue 48mm x 20mm, shaft 11mm diameter x 22mm long with 4mm dia x 3mm long peg,
floor mounted traditional dip switch for foot use, equivalent to Lucas model FS22-1, base plate measures 75mm x 40mm with 60mm hole centre fixing screws, three terminals with screw/plate...
foot operated dip switch for mounting through floor. base measures 55mm x 45mm. overall height 60mm of which switch pillar is 45mm tall, fixing holes 38mm.
Steering column mounted indicator/trafficator switch. Secures around steering column using metal band clip. Base measures 30mm deep (front to back), black bakelite type finish with plated stalk....
indicator switch which mounts to steering column, secured with a band clip thus can be removed without leaving any extra holes etc. body approx 56mm tall x 44mm deep, overall length approx 164mm...
Steer column mount indicator/trafficator switch. Secures to round steer column using metal band clip. Base measures 30mm deep (front to back), black bakelite type finish with plated stalk, overall...
Lucas SRB312 floor mounting starter button, heavy pattern for connecting into starter/battery cables. Part reference 54033241. Supplied with machined push button knob and mounting plate. Body...
12 volt remote starter button that you can mount under the bonnet for that ease of starting the engine whilst you're working on the car. 12V. Equivalent to Lucas part numbers SRB316, 2ST
floor mount starter switch for connecting directly into starter/battery cables, four mounting holes, two 5/16" terminals studs with nuts, as Lucas model ST18.
flange overall diameter 63.5mm, rear...
flange overall diameter 63.5mm, rear...
bulkhead fitting pull type starter switch (945), Lucas modet type ST19-2, applicable for 6 or 12 volt application, all metal body with rubber shielded terminals for heavy cables.
Ford part...
Ford part...
interior light switch with stainless steel cover. slides on/off, suitable for door pillar application.
cover approx 27mm x 51mm, holes 35mm.
cover approx 27mm x 51mm, holes 35mm.
small round surface mount toggle on/off switch, 28mm diameter x approx 13mm tall cover. nickel/chrome plated cover (unscrews to get to terminals). only suitable for 6 volt or 12 volt, maximum...
Interior light toggle switch with pressed stainless steel cover plate 43mm x 30mm with bevel edges.
on/off only. 24mm between hole centres.
Please note that the connection terminals will require...
on/off only. 24mm between hole centres.
Please note that the connection terminals will require...
Hazard flasher warning switch kit (12v only). Switch with illuminated knob and flasher unit mounted onto a small bracket with cover for mounting underneath the dash or steering column, which wires...
Bulkhead fitting pull type starter switch (945), as Lucas model type ST19-2, applicable for 6 or 12 volt application, metal case with PVC terminal block. Terminals for heavy cables. A lower cost...
Prices shown include VAT @ 20% where applicable
