Chrome plate bonnet catch as fitted to Morris Minor, MG J2, Wolseley Hornet etc. the catch has a kidney shape plate to allow movement. Catch size 133mm overall.
Parts
Pull bonnet catch from a Wilmot Breeden pattern as used as original equipment for Morris 8, Morgan etc. chrome on brass, approx 4.75" / 120mm long. complete with bonnet catch plate. Hole centres...
Small top quality catch, approx 4.25" / 110mm long overall, complete with catch plate, chromium plated on brass, small rubber buffer on back. base plate and catch plate same size (40mm x 19mm with...
Large top quality catch approx 135mm overall complete with catch plate, chromium or nickel plated on brass. mountings approx 90mm apart
Chrome finish
Chrome finish
Large top quality catch approx 135mm overall complete with catch plate, chromium or nickel plated on brass. mountings approx 90mm apart
Nickel finish
Nickel finish
Large top quality catch approx 135mm overall complete with catch plate, chromium or nickel plated on brass. mountings approx 90mm apart
Screw down bonnet catch which bolts to the outside of the bonnet panel, new manufacture, 4 mounting holes approx approx 28mm and 24mm apart vertically on 48mm round base, chromium top, approx 85mm...
Screw down bonnet catch which bolts to the outside of the bonnet panel, new manufacture, 4 mounting holes approx approx 28mm and 24mm apart vertically on 48mm round base, chromium top, approx 85mm...
Screw down bonnet catch which bolts to the outside of the bonnet panel, new manufacture, 4 mounting holes approx approx 28mm and 24mm apart vertically on 48mm round base, chromium top, approx 85mm...
Screw down bonnet catch which bolts to the outside of the bonnet panel, new manufacture, 4 mounting holes approx approx 28mm and 24mm apart vertically on 48mm round base, chromium top, approx 85mm...
Chrome finish on brass, tee shape twist handle fastener. push top down against spring to engage hook, turn through 90 degree to release. Lever top 52mm long, angled base approx 45mm diameter with...
Chrome finish on brass, tee shape twist handle fastener with 'R' embossed into top. push top down against spring to engage hook, turn through 90 degree to release. lever top 52mm long, angled base...
High quality spring loaded pull catch with loop finger pull ring, powder coated finish, complete with pocket. Approximately 118mm long. Chrome finger pull ring. Hook for pocket approximately 80mm...
Open spring bonnet catch, nickel plate finish, 125mm long, a good value spring catch to hold a bonnet down, supplied with top catch.
Small rubber hook with zinc plated bracket and clip. overall length approx 54mm. maximum extension from relaxed to tension not to exceed 10%.
Bonnet/hood catch supplied with pocket. polished stainless steel parts, 91mm tall overall, base 55mm wide. choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Bonnet/hood catch supplied with pocket. polished stainless steel parts, 91mm tall overall, base 55mm wide. choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Bonnet/hood catch supplied with pocket. polished stainless steel parts, 91mm tall overall, base 55mm wide. choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Remax pattern push and turn bonnet fastener catch. push handle down to engage catch on to clip (not supplied as part of vehicle) and turn handle to release catch to open bonnet. base 47mm diam...
Stainless steel bonnet catch with T bar grip pattern. 95mm long, two screw base (mount holes 35mm centres) mounts horizontally.
bonnet catch pull and locating bracket of 'squashed tube' pattern offered by Ewarts. 113mm long. finger pull is shaped off the end of the tube. base 36mm x 24mm. bonnet clip base 31mm x 22mm. we...
bonnet catch pull and locating bracket of 'squashed tube' pattern offered by Ewarts. 113mm long. finger pull is shaped off the end of the tube. base 36mm x 24mm. bonnet clip base 31mm x 22mm. we...
bonnet catch pull and locating bracket of 'squashed tube' pattern offered by Ewarts. 113mm long. finger pull is shaped off the end of the tube. base 36mm x 24mm. bonnet clip base 31mm x 22mm. we...
Prices shown include VAT @ 20% where applicable
