Replacement rubber buffer for our sliding door check restraining strap (part number 161) - 22mm diameter x 18mm long, with 13mm x 3.5mm slot.
Parts
Right angle, original Holdtite design made from the original tooling, side approximately 45mm.
Right angle, plain pattern, sides approximately 45mm long
Oval moulded black brake or clutch pedal rubber with 'M' in face for Morris applications. To fit over metal pad approx 1 9/16" x 2 5/8" (40mm x 67mm). Used on the following models Morris 8 Series...
19mm dia x 9mm high, 3mm fixing hole
25mm dia x 13mm high, 3mm fixing hole.
13mm dia x 5mm high buffer top, with cone back for fitting into a 5mm panel fixing hole
22mm dia x 5mm high buffer top with tab on base for securiung in a 12mm panel fixing hole.
19mm diameter x 15mm high buffer top, with tab insert on the base for fitting into 10mm panel fixing hole.
24mm diameter x 13mm high buffer top, with locating tab on base for fitting in to a 12mm panel fixing hole.
30mm diameter x 14mm high buffer top with fixing tab on base, for fitting into a 19mm panel fixing hole.
24mm diameter x 17mm high buffer top, with locating groove for fixing into a 19mm fixing panel hole.
17mm diameter x 14mm high buffer top with locating tab for securing in a 12mm fixing panel hole
17mm diameter x 24mm high buffer top with tab base for locating in a 12mm fixing panel hole
20mm diameter x 6mm high buffer top, with undercut coned spigot for securing in a 10mm fixing panel hole.
19mm diameter x 11mm high buffer top with tab on base for securing in an 11mm fixing panel hole.
Hollow moulded cap 20mm diameter x 11mm high with a 6mm stud hole entry into the hollow.
Rubber buffer stop with 31mm diameter x 18mm tall domed top section, with undercut coned tab for securing in a 16mm panel fixing hole.
Rubber buffer stop with 24mm diameter x 12mm high domed top, with 9mm diameter 11mm long plain fixing post for securing n a 9mm diameter panel fixing hole.
Sides angled at 60°, rounded end, approximately 30mm long sides.
Sides angled at 50°, approximately 45mm long sides, heavy corner.
Centre side rubber, approximately 35mm wide.
Moulded transmission/gearbox cover made to an original pattern for Morris 8 Series 1 & 11 vehicles
Moulded rubber gearstick gaiter originally for Morris vehicles, but with other applications. 62mm base diameter, approx 10mm top neck bore for lever, 71mm tall.
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Black rubber grommets WITH hole. For approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
6.5mm - pack of 100 pieces
8mm - pack of 100...
6.5mm - pack of 100 pieces
8mm - pack of 100...
Assortment pack of grommets WITH hole. 90 pieces in a range of sizes for 6.5mm through to 25mm diameter panel holes. For metal panel thicknesses up to 1/6mm.
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Black rubber blanking grommets for approximately 1.5mm panel thickness. Packet size varies according to grommet size - to suit panel hole of:
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
12mm - pack of 50 pieces
16mm - pack of 50 pieces...
Mixed pack of plain blanking grommets (NO hole) - assortment of 90 pieces in a range of sizes for 6.5mm through to 25mm diameter panel holes. For metal panel thicknesses up to 1.6mm thick.
Black moulded part with metal interbonded plate
Moulded rubber part, black. Slot 37mm x 15mm. Base overall 73mm x 62mm approximately. Supplied as a handed pair. On this pattern the iron passes through the face rubber at an angle.
Washer for between rear mudguard and running board, also used on exhaust silencer brackets. Approximately 25mm outside diameter, 10mm inside diameter and 5mm thick.
Black rubber moulded part, internal diameter 64mm, panel hole approx 76mm, overall diameter 100mm.
Moulded rubber transmission/gearbox cover, made to an original pattern for Morris 8 Series E and Morris 10 models. Dimensions - 235mm long x 195mm at widest, turret 68mm diameter x 35mm tall.
Fuel filler neck grommet (suits Morris 8 series E saloon and Z van). Black rubber. Internal diameter approx. 44mm, overall flange 99mm x 107mm. Note the angle of slope is approx. 25 degree from...
Moulded rubber part, supplied as a handed PAIR. Internal slot 26mm x 7mm. Base 78mm x 62mm approximately.
Moulder rubber part, 13mm diameter internal hole, base approximately 60mm round.
Moulded rubber part, 18mm internal diameter, base approximately 68mm x 63mm
Moulded rubber part, internal slot approx 35mm x 11mm, base approximately 76mm x 50mm.
Moulded rubber part, slot approx 35mm x 5mm, 'oval' shaped base 92mm x 49mm. Morris applications.
Moulded rubber part, slot 28mm x 6mm, base 70mm x 50mm approximately. Handed PAIR.
Moulded rubber part, slot 37mm x 12mm, base 100mm x 60mm approximately.
Moulded rubber part, slot 37mm x 10mm, base 106mm x 63mm. Handed PAIR.
Moulded rubber part, slot 38mm x 28mm, base 80mm x 78mm approximately. PAIR. Morris applications
Moulded rubber part, slot 35mm x 12mm, base 95mm x 55mm approximately.
Moulded rubber parts, internal hole size 35mm OR 38mm - please select you required option below. Base 87mm x 66mm approximately. Supplied as a PAIR
Moulded rubber parts, internal hole size 35mm OR 38mm - please select you required option below. Base 87mm x 66mm approximately. Supplied as a PAIR
Moulded rubber parts, internal hole size 35mm OR 38mm - please select you required option below. Base 87mm x 66mm approximately. Supplied as a PAIR
Moulded rubber part, slot 40mm x 13mm, base 123mm x 58mm approximately. Supplied as a handed pair.
Moulded rubber part, slot 41mm x 9mm, base 105mm x 70mm approximately. Supplied as a pair.
Moulded rubber part, internal diameter 30mm, base 61mm diameter approximately. PAIR
Moulded rubber part, internal size 11mm, base 84mm x 80mm approximately. Supplied as a handed pair.
Moulded rubber part, slot 54mm x 11mm, base 110mm x 70mm approximately. Supplied as a pair.
Moulded rubber part, black. Slot 36mm x 6mm. Base overall 68mm x 60mm approximately. Supplied as a handed pair. On this pattern the iron passes through the face rubber at an angle.
Moulded part, black 48mm internal diameter, fits panel hole 56mm diameter, 103mm overall diameter.
Moulded part, black 50mm internal diameter, fits panel hole 66mm diameter, 85mm overall diameter.
Moulded part for 45mm pipe. Panel hole 68mm x 55mm, overall 79mm x 66mm. All dimensions approx
Moulded part, black 56mm internal diameter, fits panel hole 72mm diameter, 100mm overall diameter.
Moulded part, black 49mm internal diameter, fits panel hole 72mm diameter, 90mm overall diameter.
Moulded part, black 52mm internal diameter, fits panel hole 62mm diameter, 85mm overall diameter.
Moulded part, black 56mm internal diameter, fits panel hole 70mm diameter, 90mm overall diameter.
Moulded part, black 45mm internal diameter angled through flange oval base 113mm x 87mm.
Moulded part, black 44mm internal diameter angled through flange base 123mm overall diameter.
Moulded part, black 57mm internal diameter, fits panel hole 69mm diameter, 83mm overall diameter.
Moulded part, black 45mm internal diameter, fits panel hole 53mm diameter, 70mm overall diameter.
Moulded part, black 54mm internal diameter, fits panel hole 64mm diameter, 88mm overall diameter.
Moulded part, black. 62mm internal diameter, fits panel hole 70mm diameter, 102mm overall diameter.
Moulded part, black 44mm internal diameter, fits panel hole 72mm diameter, 100mm overall diameter.
Moulded part, black 52mm internal diameter, fits panel hole 82mm diameter, 102mm overall diameter.
Moulded part, black 59mm internal diameter, fits panel hole 76mm diameter, 88mm overall diameter.
Black rubber cover with flat base 124mm diameter x 90mm high. Inside diameter of base 72mm, top lever hole diameter 14mm.
Replacement shaped rubber bush at end of early Armstrong friction shock absorbers. Approximate dimensions base (foot print) 46mm x 23mm, height 37mm, 26mm wide at widest point with 12mm hole...
Moulded rubber gear stick lever gaiter, 95mm base diameter, approx 12mm top neck bore for lever, 28mm tall.
black moulded rubber part. flat to one side. internal diameter 65mm, panel hole 76mm, overall 98mm diameter.
Black rubber moulded part, oval shape hole for 65mm pipe, panel hole 108mm x 85mm. Overall 130mm x 100mm. All dimensions approx.
Moulded rubber part, black. Slot 38mm x 6mm. Base overall 75mm x 64mm approximately. Supplied as a handed pair. On this pattern, the iron passes through the face rubber at right angle.
Black moulded part with metal interbonded plate.
Black rubber gear lever gaiter. Circular base, 93mm overall diameter to fit over approximately 80mm metal panel hole (maximum thickness 2.5mm). Gear stick/lever hole 15mm diameter....
Prices shown include VAT @ 20% where applicable
