Chrome on brass fixing nut for original Lucas ST38 'Pork Pie' type lamps with 4BA thread.
Parts
Chrome on brass fixing nut for reproduction 776/CA1249 part number series lamps (reproduction Lucas ST38/'Pork Pie' type lamps) with M4 fixing stud thread.
Reproduction frosted plastic lens for Lucas LD109 type side lamps. Will fit original lamps as well as 918-R and 918-T part numbered reproduction lamps.
3mm thick polyeurethane foam LENS gasket for part number series 776 and CA1249 (ST38 or 'Pork Pie') rear lamps. With semi circular cut out for rim retaining screw. Often two are used per lamp to...
1.5mm thick nitrile 70 Shore rubber LENS gasket for Lucas ST51 'D' type rear lamps (part number series 249 and 428). Suitable for solid or split lens type lamps.
Chrome on brass rim fixing nut with 2BA thread. 10mm depth of female thread. Supplied with 2BA x 3/4" slotted cheese head stainless steel screw.
Long daisy head head and spot lamp rim screw for some large Lucas headlamps including the P80, overall length 49mm (head 29mm, thread 20mm) head diameter 15mm tapering down to 9mm, with a 2BA...
Return spring for dipping reflectors used on Lucas lamps including the L150. Extension spring. 48mm long, 6.25mm diameter with one closed loop end and one open loop end. Please check dimensions...
Pair of nickel plated, cast brass rear lamp brackets suitable for divers helmet rear lamps and similar, requiring spade mounting. Oval mounting base, drilled with 8mm diameter holes at 45mm...
Dipping reflector pivot used on Lucas two piece dipping reflectors. Spring steel 'P' clip and ball bearing holds inner refector bowl and outer reflector rim togther, allowing the inner reflector...
Compression spring for use with long rim catch part no. 863A. The spring is held in place by a small roll pin inserted through the end of the catch). Makes Lucas part no assembly 532590
'Red dot' tell tale medallion for Lucas type 1130, LD109 etc side lamps. Plain finish. Overall dimensions 14mm diameter x 6.25mm deep. To fit 11.5mm hole.
Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure on lamp body as original. We stock the following sizes (measure...
Highly polished stainless steel lamp rim for single (unequal waisted) lens 'Duolamp' type lamps (our part number series CA1266)
Headlamp EPDM rim seal for many Lucas lamps including the L140, L148, L150 and L165 and L166. The flap locates in the 3mm wide groove in the bowl rim, behind where the reflector (bead type, rather...
Flat, stippled pattern glass lens, very similar to the original Lucas 'Difusa' type glass used on early headlamps. Stippled pattern on one side as original. Equivalent to Lucas part number 516173....
Flat, stippled pattern glass lens, very similar to the original Lucas 'Difusa' type glass used on early headlamps. Stippled pattern on one side as original. Equivalent to Lucas part number 505975....
Flat, stippled pattern glass lens, very similar to the original Lucas 'Difusa' type glass used on early headlamps. Stippled pattern on one side as original. Equivalent to Lucas part number L215. 9...
Domed, pressed glass 'U Flute' Lens with 5/8" wide flutes around central U pattern. Equivalent to Lucas part number 551308. 7 13/16" diameter. Suitable for Lucas type lamps L140, L148, LD147,...
Domed, pressed glass lens with 1/4" wide flutes in the lower half of the lens below and around the clear centre and upper half. Equivalent to Lucas part number 504224. 7 13/16" diameter. Suitable...
Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep amber glass, 50mm in diameter x 8mm thick, with a flat back
Highly polished stainless steel lamp rim, for split lens red/red or red/amber 'Duolamps' (our part number series 211)
Quality clear glass lens for number plate illumination cut out on 'Duolamp' type rear lamps - part number series CA1265, CA1266 and 211R
Main rim gasket for the CA1266 series single lens 'Duolamps' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
High quality plain red glass lens for single (unequal waisted) 'Duolamp' type (part number series CA1266) lamps
Number plate lens gasket for our CA1265/1266 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Main rim gasket for the CA1265 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Equivalent to Jaguar part number C2881. Bolt on side light housing for our side light part number 393 (equivalent to Lucas part number L490).
Highly polished stainless steel lamp rim for single (equal waisted) 'Duolamps' type lamps (our part number series CA1265)
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Compact bulb holder for 39mm long festoon bulbs with spade onnections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (exlcuding...
Compact bulb holder for 42 to 44mm long festoon bulbs with spade onnections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (exlcuding...
Hiqh quality clamp for tightening the bulb holder socket in the back of Lucas lamp refectors onto the BA15 bulb holder (e.g. our part numbers 853 or 153). The clip strap is formed from steel and...
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLT kit but ompatible with many other headlamp stem bolts. Black half gloss powder coated finish of machined part. Good...
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLTKIT but compatible with many other headlamp stem bolts. Chrome finish of machined part. Good weight and finish. 38mm max...
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Offered with single (equal pin) or double (offset pin) contacts.
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Offered with single (equal pin) or double (offset pin) contacts.
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Offset pin
Offered with single (equal pin) or double (offset pin) contacts.
Offset pin
7" sealed beam headlamp unit 12v 65/55watt, LHD, with side light window, three spade terminal connection. RHD unit also available.
Lucas type silver painted brass bracket. Fits inside headlamp rim, tongue fits through rim slot which then accepts daisy headed rim fixing screw, dimensions 38mm x 15mm, screw tongue 15mm wide x...
Lucas type silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw in threaded hole, dimensions 24mm x 13mm, threaded screw tongue...
Lucas type silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw in plain 5mm hole, dimensions 28mm x 13mm, threaded screw tongue...
Silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw, dimensions 36mm x 18mm, screw tongue 17mm wide x 15mm tall with 5mm slot.
Single contact BA15s bulbholder with wire tail. Measures outside 17mm x 26mm long. Note the two barb tags to the side to hold this in place.
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement acrylic red lens (Lucas 523307) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. For chrome rim, clip, gasket and screw please see our...
Replacement acrylic red and white lens (Lucas 523308) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. Chrome rim, clip, gasket and screw is our...
7" sealed beam headlamp unit 12v 65/55watt, RHD, with side light window, three spade terminal connection. LHD unit also available.
Very high quality heavy crystal glass round bulls eye lens, manufactured in transparent deep red glass, 80mm diameter with a flat back, total thickness 26mm. Smooth front and rear.
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 85mm diameter with 2mm recess around the edge which is 3.6mm thick, total thickness 8mm....
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness...
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness...
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 40mm diameter with 1mm recess around the edge which is 2.1mm thick, total thickness...
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 54mm diameter with 1mm recess around the edge which is 2.2mm thick, total thickness...
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm....
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep amber glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm....
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep amber glass, 40mm in diameter x 8mm thick, with a flat (rather than concave) back - - ...
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep red glass, 40mm in diameter x 8mm thick, with a flat (rather than concave) back - if...
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep red glass, 50mm in diameter x 8mm thick, with a flat back
Very high quality backlight crystal glass oblong prismatic lens, manufactured in transparent deep red glass, 45mm x 20mm in diameter x 8.5mm thick in the centre, with a flat back.
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep coloured glass with a flat back. Available in Red, Amber, Blue, Green & Yellow in Sizes...
Bulb holder sleeve (offset pin BAY15D) and cotton braid pig tail wires which will fit into part number 211 series 'Duolamp' type lamps to enable a small (19mm diameter) globe double contact bulb...
Replacement glass lens for 211 Duolamp, specify all red or split amber/red
Replacement glass lens for 211 Duolamp, specify all red or split amber/red
Replacement glass lens for 211 Duolamp, specify all red or split amber/red
Semaphore (orange) plastic blade lens to fit Lucas SF80 trafficator (equivalent part number 532026). Overall length 180mm.
Polished stainless steel backing cover for Lucas SF80 SE100 trafficator. overall length 195mm.
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.
Amber spare lens
Amber spare lens
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.
Clear spare lens
Clear spare lens
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.
Red spare lens
Red spare lens
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Double contact, double ended SBC/BA15D...
Double contact, double ended SBC/BA15D...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Single contact holder which accepts a...
Single contact holder which accepts a...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Double contact holder which accepts a...
Double contact holder which accepts a...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Double contact holder which accepts a...
Double contact holder which accepts a...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Double contact holder which accepts a...
Double contact holder which accepts a...
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SCC BA15S type holder, single contact, cables enter through back.
Plug for SCC BA15S type holder, single contact, cables enter through back.
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SBC BA15D type holder, double contact, cables enter through back.
Plug for SBC BA15D type holder, double contact, cables enter through back.
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Plated dish reflector to assist with light reflection in rubber divers lamp, overall diameter 55mm with 14mm hole in the centre.
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour
Flat amber lens
Flat amber lens
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour
Flat red lens
Flat red lens
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour
Replacement clear plastic sleeve lens for number plate illumination in Lucas L582 type lamps (part number series 288)
Amber glass round prismatic lens for 288A lamps - early Lucas type L582 lamps with metal rim and prismatic lenses. 40mm diameter lens with concave back to allow fitment of a standard 25mm globe...
Red glass round prismatic lens for 288A lamps - early Lucas type L582 lamps with metal rim and prismatic lenses. 40mm diameter wens with concave back to allow fitment of a standard BA15D stop/tail...
headlamp bowl for standard 7" (700) units, plastic back shell (will not rust) complete with plated retaining rim holder, adjusters and bowl to body sealing ring/gasket
British Pre-focus P36D headlamp connector with lead. Double contact with three pin bayonet bulb holder, three wires with headlamp bowl sealing grommet and soldered bullet connecters, overall...
Sealed beam headlamp connector with lead, nylon block three Lucar (6,3mm spade) connector, three wires with headlamp bowl sealing grommet and soldered bullets, overall length 850mm.
Metal Lucas type headlamp bowl for standard 7" (700) light units. Three adjuster type. Supplied with metal back shell, chrome retaining rim holder and adjusters.
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.
Clear lens
Clear lens
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.
Amber coated lens
Amber coated lens
Rubber lens O ring seal for Lucas 1130 type sidelamp (297 series lamps) with the plastic lens.
Rubber lens O-ring seal for Lucas type 1130 (297 series) sidelamps with the glass lens and chrome rim.
BRC lamp oval plate - engraved copper.
marked B.R.C. lenticulaire parabolique No (space for entry) Generateur ALPHA
measures 59mm x 26mm
marked B.R.C. lenticulaire parabolique No (space for entry) Generateur ALPHA
measures 59mm x 26mm
Single ended, double contact bulb holder. Dimensions thread diameter 19mm, overall length 38mm, flange 28.5mm. Accepts SBC BA15D bulb, rear nut removes to expose terminal contacts.
Double contact bulb holder insert, fits our 422 bulb holder, two spring loaded brass bulb contacts at one end with two wire terminals at the other, insulator body dimensions 16mm long x 16.7mm...
Double contact bulb holder for Lucas 1130 type side lamp, accepts double contact SBC BA15D parallel pin bulbs. Please note these are made to original pattern.
Prices shown include VAT @ 20% where applicable
