Parts and Spares

Parts

Price from: £6.90 Each (£8.28 inc. VAT)
Chrome on brass fixing nut for original Lucas ST38 'Pork Pie' type lamps with 2 BA thread.
Price from: £6.90 Each (£8.28 inc. VAT)
Chrome on brass fixing nut for reproduction Lucas ST38 'Pork Pie' type lamps with M4 thread.
Price from: £7.80 Each (£9.36 inc. VAT)
Reproduction frosted plastic lens for Lucas LD109 type side lamps. Will fit original lamps as well as 918-R and 918-T part numbered reproduction lamps.
Price from: £2.55 Each (£3.06 inc. VAT)
3mm thick polyeurethane foam LENS gasket for Lucas type ST38 'Pork Pie' rear lamps (part number series 776). With semi circular cut out for rim retaining screw. Often two are used per lamp to seal...
Price from: £2.95 Each (£3.54 inc. VAT)
1.5mm thick nitrile 70 Shore rubber LENS gasket for Lucas ST51 'D' type rear lamps (part number series 249 and 428). Suitable for solid or split lens type lamps. 
Price from: £16.95 Each (£20.34 inc. VAT)
Long daisy head head and spot lamp rim screw for some large Lucas headlamps including the P80, overall length 49mm (head 29mm, thread 20mm) head diameter 15mm tapering down to 9mm, with a 2BA...
Price from: £6.45 Each (£7.74 inc. VAT)
Return spring for dipping reflectors used on Lucas lamps including the L150. Extension spring. 48mm long, 6.25mm diameter with one closed loop end and one open loop end. Please check dimensions...
Price from: £6.95 Each (£8.34 inc. VAT)
Dipping reflector pivot used on Lucas two piece dipping reflectors. Spring steel 'P' clip and ball bearing holds inner refector bowl and outer reflector rim togther, allowing the inner reflector...
Price from: £4.35 Each (£5.22 inc. VAT)
Compression spring for use with long rim catch part no. 863A. The spring is held in place by a small roll pin inserted through the end of the catch). Makes Lucas part no assembly 532590
Price from: £7.90 each (£9.48 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £7.12 Each (£8.54 inc. VAT)
Highly polished stainless steel lamp rim for single (unequal waisted) lens 'Duolamp' type lamps (our part number series CA1266)
Price from: £5.95 Per 50cm (£7.14 inc. VAT)
Headlamp EPDM rim seal for many Lucas lamps including the L140, L148, L150 and L165 and L166. The flap locates in the 3mm wide groove in the bowl rim, behind where the reflector (bead type, rather...
Price from: £2.95 Each (£3.54 inc. VAT)
Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Price from: £2.95 Each (£3.54 inc. VAT)
Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Price from: £40.51 each (£48.61 inc. VAT)
6V Positive Earth. 12 Amber LED, 7 Red LED tail light. For lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully...
Price from: £38.43 each (£46.12 inc. VAT)
12V Negative Earth. 12 Amber LED, 7 Red LED tail light. For lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully...
Price from: £42.38 each (£50.86 inc. VAT)
12V Negative Earth. 12 Amber LED, 7 Red LED tail light with 4 white LED number plate light. For lamp part number 211RA-S. Two single contact equal pin BA15 bulb base connectors. High quality...
Price from: £15.25 Each (£18.30 inc. VAT)
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep amber glass, 50mm in diameter x 8mm thick, with a flat back
Price from: £7.12 Each (£8.54 inc. VAT)
Highly polished stainless steel lamp rim, for split lens red/red or red/amber 'Duolamps' (our part number series 211)
Price from: £7.90 Each (£9.48 inc. VAT)
Quality clear glass lens for number plate illumination cut out on 'Duolamp' type rear lamps - part number series CA1265, CA1266 and 211R 
Price from: £2.88 Each (£3.46 inc. VAT)
Main rim gasket for the CA1266 series single lens 'Duolamps' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Price from: £12.38 Each (£14.86 inc. VAT)
High quality plain red glass lens for single (unequal waisted) 'Duolamp' type (part number series CA1266) lamps
Price from: £2.96 Each (£3.55 inc. VAT)
Number plate lens gasket for our CA1265/1266 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Price from: £2.95 Each (£3.54 inc. VAT)
Main rim gasket for the CA1265 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Price from: £48.57 each (£58.28 inc. VAT)
Equivalent to Jaguar part number C2881. Bolt on side light housing for our side light part number 393 (equivalent to Lucas part number L490).
Price from: £7.12 Each (£8.54 inc. VAT)
Highly polished stainless steel lamp rim for single (equal waisted) 'Duolamps' type lamps (our part number series CA1265)
Price from: £11.34 Each (£13.61 inc. VAT)
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Price from: £11.34 Each (£13.61 inc. VAT)
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Price from: £11.34 Each (£13.61 inc. VAT)
Desmo bronze badge/medallion, 19mm in diameter with a 2mm hole in the centre, marked Desmo across the top, with winged car motif in the centre and Birmingham across the bottom, available in chrome...
Price from: £2.75 Each (£3.30 inc. VAT)
Compact bulb holder for 39mm long festoon bulbs with spade onnections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (exlcuding...
Price from: £2.85 Each (£3.42 inc. VAT)
Compact bulb holder for 42 to 44mm long festoon bulbs with spade onnections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (exlcuding...
Price from: £8.90 Each (£10.68 inc. VAT)
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLT kit but ompatible with many other headlamp stem bolts. Black half gloss powder coated finish of machined part. Good...
Price from: £8.90 Each (£10.68 inc. VAT)
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLTKIT but compatible with many other headlamp stem bolts. Chrome finish of machined part. Good weight and finish. 38mm max...
Price from: £3.49 each (£4.19 inc. VAT)
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Price from: £3.49 each (£4.19 inc. VAT)
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.

Price from: £3.55 each (£4.26 inc. VAT)
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.

Offset pin
Price from: £27.38 Each (£32.86 inc. VAT)
7" sealed beam headlamp unit 12v 65/55watt, LHD, with side light window, three spade terminal connection. RHD unit also available.
Price from: £9.98 Each (£11.98 inc. VAT)
Lucas type silver painted brass bracket. Fits inside headlamp rim, tongue fits through rim slot which then accepts daisy headed rim fixing screw, dimensions 38mm x 15mm, screw tongue 15mm wide x...
Price from: £9.98 Each (£11.98 inc. VAT)
Lucas type silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw in threaded hole, dimensions 24mm x 13mm, threaded screw tongue...
Price from: £9.70 Each (£11.64 inc. VAT)
Lucas type silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw in plain 5mm hole, dimensions 28mm x 13mm, threaded screw tongue...
Price from: £9.70 Each (£11.64 inc. VAT)
Silver painted brass bracket. fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw, dimensions 36mm x 18mm, screw tongue 17mm wide x 15mm tall with 5mm slot.
Price from: £10.22 each (£12.26 inc. VAT)
Single contact BA15s bulbholder with wire tail. Measures outside 17mm x 26mm long. Note the two barb tags to the side to hold this in place.
Price from: £11.28 each (£13.54 inc. VAT)
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Price from: £11.28 each (£13.54 inc. VAT)
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Price from: £11.28 each (£13.54 inc. VAT)
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Price from: £11.28 each (£13.54 inc. VAT)
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Price from: £27.56 each (£33.07 inc. VAT)
Replacement acrylic  red lens (Lucas 523307) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. For chrome rim, clip, gasket and screw please see our...
Price from: £27.50 Each (£33.00 inc. VAT)
Replacement acrylic  red and white lens (Lucas 523308) for the Lucas box type 288-3 rear number plate lamp on the rear number plate box assembly. Chrome rim, clip, gasket and screw is our...
Price from: £32.25 Each (£38.70 inc. VAT)
7" sealed beam headlamp unit 12v 65/55watt, RHD, with side light window, three spade terminal connection. LHD unit also available.
Price from: £22.34 Each (£26.81 inc. VAT)
Very high quality heavy crystal glass round bulls eye lens, manufactured in transparent deep red glass, 80mm diameter with a flat back, total thickness 26mm. Smooth front and rear.
Price from: £21.15 Each (£25.38 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 85mm diameter with 2mm recess around the edge which is 3.6mm thick, total thickness 8mm....
Price from: £15.29 Each (£18.35 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness...
Price from: £15.29 Each (£18.35 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness...
Price from: £11.16 Each (£13.39 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 40mm diameter with 1mm recess around the edge which is 2.1mm thick, total thickness...
Price from: £15.29 Each (£18.35 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 54mm diameter with 1mm recess around the edge which is 2.2mm thick, total thickness...
Price from: £15.29 Each (£18.35 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm....
Price from: £16.45 Each (£19.74 inc. VAT)
Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep amber glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm....
Price from: £12.33 Each (£14.80 inc. VAT)
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep amber glass, 40mm in diameter x 8mm thick, with a flat (rather than concave) back - - ...
Price from: £12.33 Each (£14.80 inc. VAT)
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep red glass, 40mm in diameter x 8mm thick, with a flat (rather than concave) back -  if...
Price from: £15.86 Each (£19.03 inc. VAT)
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep red glass, 50mm in diameter x 8mm thick, with a flat back
Price from: £14.98 Each (£17.98 inc. VAT)
Very high quality backlight crystal glass oblong prismatic lens, manufactured in transparent deep red glass, 45mm x 20mm in diameter x 8.5mm thick in the centre, with a flat back.
Price from: £1.95 Each (£2.34 inc. VAT)
Very high quality backlight crystal glass round faceted prismatic lens, manufactured in transparent deep coloured glass with a flat back. Available in Red, Amber, Blue, Green & Yellow in Sizes...
Price from: £14.36 each (£17.23 inc. VAT)
Bulb holder sleeve (offset pin BAY15D) and cotton braid pig tail wires which will fit into part number 211 series 'Duolamp' type lamps to enable a small (19mm diameter) globe double contact bulb...
Price from: £17.46 each (£20.95 inc. VAT)
Replacement glass lens for 211 Duolamp, specify all red or split amber/red
Price from: £17.80 each (£21.36 inc. VAT)
Replacement glass lens for 211 Duolamp, specify all red or split amber/red

Price from: £17.46 each (£20.95 inc. VAT)
Replacement glass lens for 211 Duolamp, specify all red or split amber/red

Price from: £8.64 each (£10.37 inc. VAT)
Semaphore (orange) plastic blade lens to fit Lucas SF80 trafficator (equivalent part number 532026). Overall length 180mm. 
Price from: £8.60 each (£10.32 inc. VAT)
Polished stainless steel backing for SF80 trafficator. overall length 195mm.
Price from: £3.89 each (£4.67 inc. VAT)
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.

Amber spare lens
Price from: £3.89 each (£4.67 inc. VAT)
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.

Clear spare lens
Price from: £3.89 each (£4.67 inc. VAT)
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.

Red spare lens
Price from: £3.89 each (£4.67 inc. VAT)
Replacement plastic side lens (44mm dia x 2mm thick) for the rubber divers type lamp - available in clear, red or amber plastic.
Price from: £4.95 each (£5.94 inc. VAT)
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact

Double contact, double ended SBC/BA15D...
Price from: £4.95 each (£5.94 inc. VAT)
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact
Price from: £13.99 each (£16.79 inc. VAT)
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact

Single contact holder which accepts a...
Price from: £14.99 each (£17.99 inc. VAT)
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body. Offered in single or double contact

Double contact holder which accepts a...
Price from: £8.75 each (£10.50 inc. VAT)
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Price from: £8.75 each (£10.50 inc. VAT)
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.

Plug for SCC BA15S type holder, single contact, cables enter through back.
Price from: £8.75 each (£10.50 inc. VAT)
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.

Plug for SBC BA15D type holder, double contact, cables enter through back.
Price from: £8.81 Each (£10.57 inc. VAT)
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Price from: £8.81 Each (£10.57 inc. VAT)
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Price from: £8.81 Each (£10.57 inc. VAT)
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Price from: £13.81 each (£16.57 inc. VAT)
Plated dish reflector to assist with light reflection in rubber divers lamp, overall diameter 55mm with 14mm hole in the centre.
Price from: £4.40 each (£5.28 inc. VAT)
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour

Flat amber lens
Price from: £4.40 each (£5.28 inc. VAT)
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour

Flat red lens
Price from: £4.40 each (£5.28 inc. VAT)
Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber divers lamps, please specify colour
Price from: £8.34 Each (£10.01 inc. VAT)
Replacement clear plastic sleeve lens for number plate illumination in Lucas L582 type lamps (part number series 288)
Price from: £12.33 Each (£14.80 inc. VAT)
Amber glass round prismatic lens for 288A lamps - early Lucas type L582 lamps with metal rim and prismatic lenses. 40mm diameter lens with concave back to allow fitment of a standard BA15D bulb.
Price from: £12.33 Each (£14.80 inc. VAT)
Red glass round prismatic lens for 288A lamps - early Lucas type L582 lamps with metal rim and prismatic lenses. 40mm diameter wens with concave back to allow fitment of a standard BA15D stop/tail...
Price from: £19.98 each (£23.98 inc. VAT)
headlamp bowl for standard 7" (700) units, plastic back shell (will not rust) complete with plated retaining rim holder, adjusters and bowl to body sealing ring/gasket
Price from: £13.41 each (£16.09 inc. VAT)
British Pre-focus P36D headlamp connector with lead. Double contact with three pin bayonet bulb holder, three wires with headlamp bowl sealing grommet and soldered bullet connecters, overall...
Price from: £8.95 each (£10.74 inc. VAT)
Sealed beam headlamp connector with lead, nylon block three Lucar (6,3mm spade) connector, three wires with headlamp bowl sealing grommet and soldered bullets, overall length 850mm.
Price from: £37.26 each (£44.71 inc. VAT)
Metal Lucas type headlamp bowl for standard 7" (700) light units. Three adjuster type. Supplied with metal back shell, chrome retaining rim holder and adjusters.
Price from: £16.55 each (£19.86 inc. VAT)
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.
Price from: £16.55 each (£19.86 inc. VAT)
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.

Clear lens
Price from: £16.55 each (£19.86 inc. VAT)
Plastic front lens for our 297 (Lucas 1130 type) sidelamps. Purchase with O-ring seal part number 361A.

Amber coated lens
Price from: £0.71 each (£0.85 inc. VAT)
Rubber lens O ring seal for Lucas 1130 type sidelamp (297 series lamps) with the plastic lens.
Price from: £0.64 Each (£0.77 inc. VAT)
Rubber lens O-ring seal for Lucas type 1130 (297 series) sidelamps with the glass lens and chrome rim.
Price from: £14.68 each (£17.62 inc. VAT)
BRC lamp oval plate - engraved copper.
marked B.R.C. lenticulaire parabolique No (space for entry) Generateur ALPHA
measures 59mm x 26mm
Price from: £16.73 each (£20.08 inc. VAT)
Single ended, double contact bulb holder. Dimensions thread diameter 19mm, overall length 38mm, flange 28.5mm. Accepts SBC BA15D bulb, rear nut removes to expose terminal contacts.
Price from: £4.95 Each (£5.94 inc. VAT)
Double contact bulb holder insert, fits our 422 bulb holder, two spring loaded brass bulb contacts at one end with two wire terminals at the other, insulator body dimensions 16mm long x 16.7mm...
Price from: £17.35 each (£20.82 inc. VAT)
Double contact bulb holder for Lucas 1130 type side lamp, accepts double contact SBC BA15D parallel pin bulbs. Please note these are made to original pattern.
Price from: £51.18 pair (£61.42 inc. VAT)
Two bulbs (amber for flasher, clear for sidelamp) - 12 volt ONLY - bulb holder for fitting into Lucas type 1130 sidelamps - our 297 part number series. Supplied in pairs only. Mounting plate...
Price from: £9.35 each (£11.22 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Price from: £6.90 each (£8.28 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £6.90 each (£8.28 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £7.00 each (£8.40 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £7.70 each (£9.24 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £8.49 each (£10.19 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £9.35 each (£11.22 inc. VAT)
Reproduction 'King of the Road' Lucas type badge. Chrome plate on brass pressings with lugs on rear to peen over and secure as original. We stock the following sizes (measure overall diameter of...
Price from: £5.70 each (£6.84 inc. VAT)
Raydot brass lamp badge medallion, 17mm diameter across the top 15.5mm approx below lip, fits into a 15.5mm hole, marked RAYDOT LTD in the centre with Made in England around the edge, brass only...
Price from: £7.99 each (£9.59 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Price from: £7.99 each (£9.59 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Price from: £9.35 each (£11.22 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Price from: £9.35 each (£11.22 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Price from: £10.70 each (£12.84 inc. VAT)
reproduction Rotax badge. chrome plate on brass casting with lugs on rear to peen over and secure as original. we stock the following sizes (measured across outside of badge). very small - 15.7mm...
Prices shown include VAT @ 20% where applicable