Small spring used in Lucas CWX type wiper motors - 3.6mm OD, 12mm free length, 0.3mm wire diameter.
Parts
Large spring used in Lucas CWX type wiper motors - 6.4mm OD, 34mm free length, 0.6mm wire diameter.
Lucas CWX type wiper motor spindle. Made from brass. 165mm long, 5mm diameter, 6mm long threaded section at one end, three cross holes 1.5mm diameter at 20mm, 34mm and 88mm from the threaded...
Plastic spacer for Lucas CWX type motors. 48mm long x 19mm wide with radiused corners, 6.5mm thick. Two mounting holes 4.75mm diameter, 39mm between centres. Central hole 10.5mm diameter. All 3...
Plastic spacer for Lucas CWX type motors complete with metal spindle tube. 48mm long x 19mm wide with radiused corners, 13mm thick. Mounting holes 4.75mm diameter with counterbore recess 6.25mm...
Cork spacer/gasket for Lucas CWX type motors. 48mm long x 19mm wide with radiused corners, 3mm thick. Two mounting holes 4mm diameter, 39mm between centres. Central hole 6.5mm diameter. All 3 hole...
Carbon brush with copper wire connection for Lucas type CWX wiper motors. 11mm x 5mm x 4.25mm
Crome finished die cast lever arm for rear of Lucas CWX type wiper motor case. 36mm long arm with locating pin in end. 27mm total depth, 5.25mm bore through spindle, with 6mm counter bore 9mm deep...
Windscreen washer accessory kit – two black double/twin washer jets, a tee piece, a straight connector, 1.8m plastic tube, a wiring loom, push switch, clips for the tube, a bracket, bolts...
Clear plastic windscreen washer system tube - 6.25mm OD and 3.75mm ID. Sold by the metre.
Double jet, nickel plated. Approximate 13mm diameter. Requires 7.7mm hole through metal panel, pipe connection 4.5mm. Equivalent to Lucas WSB131 type jet.
Single jet, small (8mm diameter), chrome plate. Requires 4.65mm hole through metal panel, pipe connection 3.5mm. Equivalent to Lucas WSB136 type jet.
Black vacuum wiper system tubing, 1/8" (3.25mm) ID x 5/16" (8mm) OB with fine ribs.
as drawing, black, 6mm spindle hole, approx 11mm circular panel hole.
as drawing, black, 6mm spindle hole, 13mm approx circular panel hole.
angled as sketch, black, 6mm spindle hole, 13mm x 16mm approx oval panel hole.
angled as sketch, black, 6mm spindle , 12mm x 17mm approx oval panel hole.
andles as sketch, black, 6mm spindle, 15mm approx wide panel hole cut on angle.
angled as sketch, 6mm spindle hole, 16mm approx panel hole.
angled as sketch, black, 6mm spindle hole, 17mm x 19mm approx oval panel hole.
equivalent to Lucas 733874
equivalent to Lucas 733874
as sketch, black, 6mm spindle hole, 15mm approx circular panel hole.
equivalent to Lucas 729313
equivalent to Lucas 729313
angled as sketch, 6mm spindle hole, 16mm x 22mm oval panel hole.
as sketch, black, 6mm spindle hole, 20mm approx circular panel hole.
as sketch, black, 6mm spindle hole, 13mm approx circular panel hole.
as sketch, black, 4.5mm spindle hole, 20mm approx circular panel hole.
Dimensions as sketch. Black, 6mm spindle hole, 24mm x 29mm approx oval panel hole.
angled as sketch, black, 6mm spindle hole, 17mm approx panel hole.
equivalent to Lucas 735679
equivalent to Lucas 735679
As sketch, black, 6mm spindle hole, 15mm approximately circular panel hole.
Equivalent to Lucas 734652
Equivalent to Lucas 734652
moulded part, 8mm inner hole, 13mm outer neck, 22mm diameter.
as drawing, black, 8mm spindle hole, approx 11mm circular panel hole.
angled as sketch, black, 6mm spindle hole, 15mm x 24mm approx oval panel hole.
3 x 1/4" diameter stud wiper motor fixing for Lucas CR and CRT wiper motors. Equivalent to Lucas part number 741583, overall dimensions 53mm at widest x 75mm long.
Windscreen washer pump, manual push black plastic button, dimensions 80mm overall length, 42mm diameter at widest point (rear flange), main body 34mm, 15mm diameter mounting boss thread. Will fit...
Plastic washer bottle kit with built in 12 volt pump with mounting bracket. 170mm tall (185mm including cap) x 140mm wide x 70mm deep, mounting bracket 60mm wide tapering to 45mm wide, 69mm tall....
Larger capacity plastic washer bottle kit with built in 12 volt pump with mounting bracket. 180mm tall (190mm including cap) x 120mm wide x 100mm deep, mounting bracket 65mm wide and 75mm tall...
Adaptor to enable the fitting of a spline shaft wiper arm on to a shaft. Secures with a pinch bolt. Dimensions 20mm tall with a19mm diameter base, central bore 6mm (7/32"), 13.6mm spline.
Wiper motor stop plate as fitted to CW1, CWX and CWH screen mounted wiper motors, restricts wiper arm sweep. Made from 2.4mm thick powered coated steel, face plate 63mm wide x 18mm tall with two...
Prices shown include VAT @ 20% where applicable
