90 degree male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Dash 3 hose finisher for use on hose assemblies with push-on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -3 hose.

90 degree male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive clamp or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburetor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburetor installations.

Straight 1/8" NPTF (tapered) male to 5/16" ID hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low-pressure (up to 15psi) carburettor installations.

17-19mm rubber end cap for 3/8" hose Use with our 19mm OD  SSFH3/8 Braided Hose  

14 -16mm rubber end cap for OD hose 5/16" hose Use with our 15mm OD SSFH5/16 Braided Hose 

11 -13mm rubber end cap for 1/4" hose  Use with our 13mm OD SSFH1/4 Braided Hose

Y piece with hose tail fittings for 3/8" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Straight female to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight female to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

3/8" BSP Straight male to 3/8" ID hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low-pressure (up to 15psi) carburettor installations.

Straight 3/8" BSP male to 5/16" ID hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low-pressure (up to 15psi) carburettor installations.

Straight 1/4" male to 3/8" hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low-pressure (up to 15psi) carburettor installations.

Straight 3/8" BSP male to 1/4" hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low-pressure (up to 15psi) carburettor installations.

5/16" ID Stainless Steel Braided Fuel Hose (>2<8mpg). 0.49" OD. Less bulky than the BSAu108 compliant hose. Priced PER METER Can use BRCF7 brass ferrule ends or STCF7 Zinc Ferrule

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Chrome hose finisher for use on hose assemblies with push on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -10 hose, or for -8 (or 1/2") hose fitted with stainless steel over braid

Chrome hose finisher for use on hose assemblies with push on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -12 hose, or for -10 (or 5/8") hose fitted with stainless steel over braid.

Dash 4 Hose finisher for use on hose assemblies with push-on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -4 hose.

Dash 8 Hose finisher for use on hose assemblies with push on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -8 hose. Suitable for 5/16 Stainless braided fuel hose

Unequal T piece with hose tail fittings for 3/8 and 5/16" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

BSAU108 5/16" ID Fuel Hose - single textile braid reinforcement and smooth black neoprene cover. 0.58" OD. Priced PER METER Use with our ZNBC14 hose clips

BSAU108 3/8" ID Fuel Hose - single textile braid reinforcement and smooth black neoprene cover 0.64" OD. Priced PER METER Use with our ZNBC16 hose clips

BSAU108 1/4" ID Fuel Hose - single textile braid reinforcement and smooth black neoprene cover. 0.5" OD. Priced PER METER Use with our ZNBC12 hose clips

1/4" ID Stainless Steel Braided Fuel Hose (>8mpg). 0.45" OD. Less bulky than the BSAu108 compliant hose. Priced PER METER

3/8" ID Stainless Steel Braided Fuel Hose (<2mpg) 0.56" OD. Less bulky than the BSAu108 compliant hose. Priced PER METER

3/8'' (10mm) bore. Transparent reinforced flexible tubing. Use tail piece and `O' clips to secure.

Dash 6 Hose finisher for use on hose assemblies with push on fittings to hide unsightly ends, especially where stainless braid is used. Integral worm drive clamp and chrome finish. For -6 hose.

T piece with hose tail fittings for 1/4" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Y piece with hose tail fittings for 1/4" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

T piece with hose tail fittings for 3/8" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

T piece with hose tail fittings for 5/16" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Y piece with hose tail fittings for 5/16" ID hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Steel Step Up Hose Joiner - from 1/4" To 5/16" ID Hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Steel Hose Joiner For 1/4" ID Hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Steel Hose Joiner For 3/8" ID Hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Steel Step Up Hose Joiner from 5/16in To 3/8in ID Hose.Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Steel Hose Joiner For 5/16" ID Hose. Assemble with swage ferrule, O clamps, worm drive or nut and bolt clamps. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive clamp or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

90 degree male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

90 degree male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

Straight male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

90 degree male to hose tail fitting. Assemble with swage ferrule, O clamp, worm drive or nut and bolt clamp. Suitable for low pressure (up to 15psi) carburettor installations.

5/16'' (8mm) bore. Transparent reinforced flexible tubing. Use tail piece and `O' clips to secure.

1/4'' (6mm) bore. Transparent reinforced flexible tubing. Use tail piece and `O' clips to secure.

For 5/16'' (8mm) tube

Brass BSP threaded nut and push on hose connector fitting

Brass BSP threaded nut and push on hose connector fitting -- 3/8"BSP nut for 3/8" push on pipe

Brass BSP threaded nut and push on hose connector fitting -- 1/4"BSP nut for 5/16" pipe

Brass BSP threaded nut and push on hose connector fitting -- 1/4"BSP nut for 1/4" push on pipe