Pair of nickel plated, cast brass rear lamp brackets suitable for diver's helmet rear lamps and similar, requiring spade mounting. Oval mounting base, drilled with 8mm diameter holes at 45mm centres. 76mm tall x 31mm wide, mounting bar 80mm long with lamp spade parallel to base for fitting on the rear of a vehicle. Spade dimensions 30mm wide x 41mm tall x 5mm thick. Cast in brass then polished and nickel plated. Please note - these are sand castings, so cannot be plated to the same standard as bronze lost wax/investment castings and there will be some slight marks in places in the plating. A very nice mounting set for our nickel plated CA1177 part number series lamps.

A chrome plated lamp bracket for use with badge bars, enabling you to mount Lucas 700 or 576 series spot or fog lamps on either a 19mm (3/4") or 25mm (1") badgebar. Length 68mm -- A solid, good quality bracket for 3/4" bars

A chrome plated lamp bracket for use with badge bars, enabling you to mount Lucas 700 or 576 series spot or fog lamps on either a 19mm (3/4") or 25mm (1") badgebar. Length 68mm -- A solid, good quality bracket for 1" bars

A chrome plated lamp bracket for use with badge bars, enabling you to mount Lucas 700 or 576 series spot or fog lamps on either a 19mm (3/4") or 25mm (1") badgebar. Length 68mm

Cast brass rear lamp bracket suitable for diver's helmet rear lamp and similar, requiring spade mounting, oval mounting base (undrilled) 76mm tall x 31mm wide, mounting bar 80mm long with lamp spade 90° to base for fitting on the side of a vehicle, spade dimensions 30mm wide x 41mm tall x 5mm thick. Cast in brass, can be polished and plated by customer.

Cast brass rear lamp bracket suitable for divers helmet rear lamp and similar requiring spade mounting, oval mounting base (undrilled) 76mm tall x 31mm wide, mounting bar 80mm long with lamp spade parallel to base for fitting on the rear of a vehicle, spade dimensions 30mm wide x 41mm tall x 5mm thick. Cast in brass, can be polished and plated by customer.

Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the 'underside' when fitted, approx. 105mm. 3 holes for mounting to vehicle - approx 72mm wide 2 holes for mount of lamp - approx 45mm wide

Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the 'underside' when fitted, approx. 105mm. 3 holes for mounting to vehicle - approx 72mm wide 2 holes for mount of lamp - approx 45mm wide -- For mounting on right side

Steel rear lamp bracket suitable for divers helmet rear lamps and similar, requiring spade mounting. This part is pre-fabricated and supplied undrilled. Overall height approx 125mm. Fitting to the car (rear chassis cross member) can be via a U bolt. The spade can be drilled if required to thread the rear lamp bolt through. Flat blades measures approx 24mm wide x 4mm thick and 29mm wide x 3mm thick for lamp.

Licence plate/number plate bracket which bolts under rear lamp. Available in polished stainless steel finish only

Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the 'underside' when fitted, approx. 105mm. 3 holes for mounting to vehicle - approx 72mm wide 2 holes for mount of lamp - approx 45mm wide -- For mounting on left side