Recessed lamp approximately 72mm diameter with rubber boot and body. Chrome rim with clear glass lens 45mm deep. Supplied with AMBER bulb. Equivalent to Lucas lamp model L594 with raised lens. SCC BA15S bulb holder. For spare 12V AMBER bulbs please see B343.

Small, best selling lamp of modern manufacture particularly suitable for flashing indicator use. Chrome plated body with amber lens. Body approximately 58mm diameter x 70mm long. Single mounting stud, with M8 x 1.25 pitch thread. Uses an SCC BA15S bulb. For bulbs, please see our B244 (6v) or B245 (12v).

Free standing chrome body rectangular indicator lamp with amber lens, lens 60mm x 45mm, 52mm deep. Mounting by single 10mm bolt through which wire passes. SBC BA15D bulb base. Fitted with 12 volt 10w/5w twin filament bulb. For spare bulbs, please see bulbs B3214-equal (B3214A) 6v, or B3212-equal (B3212A) 12v.

Recessed lamp, approximately 72mm in diameter with rubber boot and body. Chrome rim with amber glass lens 45mm deep. Equivalent to Lucas model L594 with raised lens. Panel hole for fixing 35mm. Supplied with a BAY15D bulb holder - for use as an indicator just wire one connection. For bulbs please see our B384 (6v) or B380 (12v).

Recessed lamp with rubber boot and body. Approximately 74mm diameter. Chrome rim. Clear glass lens with AMBER bulb. 25mm depth from mounting panel. Lucas model L488 with flat lens. Mounts through 35mm panel hole. SCC BA15S bulb holder. For 12V AMBER bulbs please see B343.

Indicator lamp of vintage appearance, modelled as the equivalent of the Lucas rear lamp type 582. Amber plastic lens 55mm diameter, body 58mm long x 42mm diameter, overall length 92mm. Chrome body. We have commissioned production of this lamp to enable older vehicles to comply to more modern traffic conditions, with a larger plastic lens on a period looking flashing indicator lamp. Accepts BA15D indicator/warning bulbs, for spare bulbs please see our B319 (6v) or B335 (12V).

Toby black ST38/'Pork Pie' type lamp with standard (three BA15S) bulb holder arrangement, fitted with a LED light board and split Red/Amber lens for Stop, Tail, INDICATOR & Number Plate illumination operation. Suitable for 6 or 12V, Negative Earth vehicles. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination. The board is fitted with three BA15S bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection illuminates the AMBER indication/turn signal LEDs. The LED board has a very low power requirement and provides great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus a good distinction between STOP and TAIL brightness's. Fully assembled and ready to fit. Please note that the indicator function requires use of an electronic flasher unit e.g.12V LEDFLASH3. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.

Chrome split lens rear 'D' lamp, equivalent to the original Lucas ST51 type lamp, though converted for combined stop, tail, number plate illumination and indicator/turn signal function, fitted with an all in one LED light board and split Red/Amber lenses giving Stop, Tail, INDICATOR & number plate illumination operation. On board electronics make this product suitable for 6V &12V vehicles, either Positive or Negative earth. The product features a main, D shaped light board with two sections of LEDs - one RED and one AMBER - that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one bulb base BA15D connector on 15cm connecting wires and one BA15S bulb base connector on 10cm connecting wires. One terminal of the BA15D base illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second terminal illuminates the Stop light (second brightness RED). The BA15S connection illuminates the AMBER indication/turn signal LEDs. These boards have a very low power requirement and provide great all over lens lighting from 27 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightness's. Fully assembled and ready to fit. Please note that the indicator function requires use of an electronic flasher unit e.g. LEDFLASH3

Black split lens rear 'D' lamp, equivalent to the original Lucas ST51 type lamp, though converted for combined stop, tail, number plate illumination and indicator/turn signal function. fitted with an all in one LED light board and split Red/Amber lenses giving Stop, Tail, INDICATOR & number plate illumination operation. On board electronics make this product suitable for 6V &12V vehicles, either Positive or Negative earth. The product features a main, D shaped light board with two sections of LEDs - one RED and one AMBER - that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one bulb base BA15D connector on 15cm connecting wires and one BA15S bulb base connector on 10cm connecting wires. One terminal of the BA15D base illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second terminal illuminates the Stop light (second brightness RED). The BA15S connection illuminates the AMBER indication/turn signal LEDs. These boards have a very low power requirement and provide great all over lens lighting from 27 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightness's. Fully assembled and ready to fit. Please note that the indicator function requires use of an electronic flasher unit e.g. LEDFLASH3

Rear 'D' lamp, equivalent to the original Lucas ST51 type lamp, though converted for combined stop, tail, number plate illumination and indicator/turn signal function. 12V only with incandescent bulbs - though there are LED options that operate with 6 or 12V - please see information below regarding B117LEDWW-A (number plate), B921LEDW-A (indicator) and B383LEDWW or B381LEDWW (6 and 12v stop and tail). Body 87mm wide x 75mm tall x 54mm deep, backing base plate 95mm wide x 84mm tall.  These high quality reproduction lamps feature a steel body and back plate with a new moulded split RED and AMBER main plastic lens, plus CLEAR side lens. Two single contact WEDGE T10 capless bulb holders - for Number Plate illumination and Indicator function - and one BA15D holder for 'Stop' and Tail function. We offer this lamp in a choice of black paint or chrome plated finish, both with side number plate illumination window. Supplied complete with 2 x capless T10 base bulbs - 1 x 5w number plate illumination light and 1 x 21W indicator - and 1 x BA15D 21/5w 'stop' and tail. For spare 12V bulbs - please see B501 for number plate, B921 (B921-12V) for indicator and B3212A (B3212-equal) for stop and tail. For LED upgrade bulbs please see 'Related Products' below - part numbers B117LEDW-A, B921LEDW-A and B381LEDW which will work with 6, 12 and 24V systems, noting you may need an LED flasher unit e.g. LEDFLASH3 --

Rear 'D' lamp, equivalent to the original Lucas ST51 type lamp, though converted for combined stop, tail, number plate illumination and indicator/turn signal function. 12V only with incandescent bulbs - though there are LED options that operate with 6 or 12V - please see information below regarding B117LEDWW-A (number plate), B921LEDW-A (indicator) and B383LEDWW or B381LEDWW (6 and 12v stop and tail). Body 87mm wide x 75mm tall x 54mm deep, backing base plate 95mm wide x 84mm tall.  These high quality reproduction lamps feature a steel body and back plate with a new moulded split RED and AMBER main plastic lens, plus CLEAR side lens. Two single contact WEDGE T10 capless bulb holders - for Number Plate illumination and Indicator function - and one BA15D holder for 'Stop' and Tail function. We offer this lamp in a choice of black paint or chrome plated finish, both with side number plate illumination window. Supplied complete with 2 x capless T10 base bulbs - 1 x 5w number plate illumination light and 1 x 21W indicator - and 1 x BA15D 21/5w 'stop' and tail. For spare 12V bulbs - please see B501 for number plate, B921 (B921-12V) for indicator and B3212A (B3212-equal) for stop and tail. For LED upgrade bulbs please see 'Related Products' below - part numbers B117LEDW-A, B921LEDW-A and B381LEDW which will work with 6, 12 and 24V systems, noting you may need an LED flasher unit e.g. LEDFLASH3 --

Torpedo style side lamp, reproduction of the Lucas 1130 type. Chromium plated body approx 100mm long x 46mm diameter, amber plastic moulded lens. Double filament bulb holder (allows combined side and flasher bulb to be fitted), mounted by two bolt in base. Rubber mounting pad supplied. Uses a BA15B bulb, for spare bulbs please see our B383 (6v) or B381 (12v).

Toby vintage round rear lamp, equivalent to the original Lucas ST38 or 'Pork Pie' type lamp. 12V ONLY with conventional bulbs - though LED upgrade bulbs are available for 6, 12 and 24V application - please see part number CA1249LEDBK, noting that you may need an LED flasher unit e.g. LEDFLASH3. Converted for combined stop, tail, number plate illumination and indicator/turn signal function. 90mm diameter x 65mm deep. These high quality reproduction lamps feature a brass body and rim with a high quality split RED and AMBER main plastic lens plus optional CLEAR side lens. Three single contact WEDGE T10 capless bulb holders. We offer this lamp in a choice of gloss black enamel or chrome plated finish, with and without side number plate illumination window. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. Uses 3 x capless T10 base bulbs - 1 x 5w tail light, 1 x 21w stop light, 1 x 21W indicator. For spare conventional bulbs - please see B501 for tail light/number plate illumination and B921 for stop light and indicator. --

Toby vintage round rear lamp, equivalent to the original Lucas ST38 or 'Pork Pie' type lamp. 12V ONLY with conventional bulbs - though LED upgrade bulbs are available for 6, 12 and 24V application - please see part number CA1249LEDBK, noting that you may need an LED flasher unit e.g. LEDFLASH3. Converted for combined stop, tail, number plate illumination and indicator/turn signal function. 90mm diameter x 65mm deep. These high quality reproduction lamps feature a brass body and rim with a high quality split RED and AMBER main plastic lens plus optional CLEAR side lens. Three single contact WEDGE T10 capless bulb holders. We offer this lamp in a choice of gloss black enamel or chrome plated finish, with and without side number plate illumination window. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. Uses 3 x capless T10 base bulbs - 1 x 5w tail light, 1 x 21w stop light, 1 x 21W indicator. For spare conventional bulbs - please see B501 for tail light/number plate illumination and B921 for stop light and indicator. --

Toby vintage round rear lamp, equivalent to the original Lucas ST38 or 'Pork Pie' type lamp. 12V ONLY with conventional bulbs - though LED upgrade bulbs are available for 6, 12 and 24V application - please see part number CA1249LEDBK, noting that you may need an LED flasher unit e.g. LEDFLASH3. Converted for combined stop, tail, number plate illumination and indicator/turn signal function. 90mm diameter x 65mm deep. These high quality reproduction lamps feature a brass body and rim with a high quality split RED and AMBER main plastic lens plus optional CLEAR side lens. Three single contact WEDGE T10 capless bulb holders. We offer this lamp in a choice of gloss black enamel or chrome plated finish, with and without side number plate illumination window. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. Uses 3 x capless T10 base bulbs - 1 x 5w tail light, 1 x 21w stop light, 1 x 21W indicator. For spare conventional bulbs - please see B501 for tail light/number plate illumination and B921 for stop light and indicator. --

Chrome pedestal indicator lamp, lens diameter 35mm, overall lamp body dimensions 50mm diameter x 60mm deep. Stem 50mm long (15mm (and 15mm diameter) plain section plus thread 35mm). M8 thread. Uses an SCC BA15S bulb. For spare bulbs please see our B317 (6v) or B382 (12v).

Indicator lamp as Lucas L563 with amber lens. Applications include Jaguar Mk2 and XK150 indicator light. Uses an SCC BA15S bulb. For bulbs, please see our B317 (6v) or B382 (12v). Equivalent alternative part number 52479.

Very small chrome warning/indicator lamp with amber lens. (40mm x 25mm x 40mm depth). Please note that this unit accepts MCC BA9S bulbs, most of which do not have the watts available for 21w/42w electronic flasher units - though please see 23W B419 (Halogen) or LED BA9S base options. Or opt for a mechanical flasher unit such as part number 414.

Flush back indicator lamp (without rubber boot. Approximately 72mm diameter rubber back. Stainless steel rim with a choice of plastic or glass lens. Uses a 42mm x 15mm 21 watt festoon bulb. A useful lamp where additional lamps are required, without the need to cut large holes. Two mounting bolts to rear. Offered with amber lens for indicator, red lens for rear stop or tail application or clear lens for side or reverse. For spare bulbs please see our B1240 (6v) or B273 (12v) for indicator, stop or reverse and B258 (12V) for tail, side. --

Flush back indicator lamp (without rubber boot. Approximately 72mm diameter rubber back. Stainless steel rim with a choice of plastic or glass lens. Uses a 42mm x 15mm 21 watt festoon bulb. A useful lamp where additional lamps are required, without the need to cut large holes. Two mounting bolts to rear. Offered with amber lens for indicator, red lens for rear stop or tail application or clear lens for side or reverse. For spare bulbs please see our B1240 (6v) or B273 (12v) for indicator, stop or reverse and B258 (12V) for tail, side. --

Chrome pedestal indicator lamp, lens diameter 35mm, overall lamp body dimensions 50mm diameter x 60mm deep. Stem 75mm long (including thread 25mm) x 10mm diameter. Uses an SCC BA15S bulb - for spare bulbs please see our B317 (6v) or B382 (12v). Sold as a pair.

Chrome pedestal indicator lamp with full lens, lens diameter 50mm, overall lamp body dimensions 50mm diameter x 70mm deep. Stem 50mm long (15mm plain section - 15mm diameter - plus 35mm threaded section). M8 thread. Uses an SCC BA15S bulb. For spare bulbs please see our B317 (6v) or B382 (12v).

Lucas type L874 Chrome pedestal indicator lamp, lens diameter 65mm x 35mm deep, overall lamp body depth 92mm tapering at the back to 30mm. Stem 80mm long (including thread 19mm) x 10mm diameter. Uses an SCC BA15S bulb - for spare bulbs please see our B317 (6v) or B382 (12v).

Reproduction CAV pattern Torpedo side lamps, chrome or nickel plated. Fitted with circular chrome or nickel on brass 'Toby' badge on top, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. A knurled rim holds the clear curved bulls eye glass lens. These lamps are made to the shape of the original CAV lamp, with the body hand spun in copper to achieve the fine point of the original pattern. Approximately 71mm diameter x 137mm long. base 91mm x 31mm with 71mm mounting hole centres. Double contact bulbholder fitted. Sold in pairs only. Uses BA15D bulbs, for spare bulbs please see our B206 (6v) or B209 (12v) -- Internally modified to accept two individual bulbs which provide a clear side lamp and an amber flashing lamp, 12 volt bulbs supplied only. For spare bulbs please see our B209 side light and B288-Amber indicator.

Early pattern cylindrical rear lamp equivalent to Lucas type 582. With side number plate illumination in stop and tail lamp configuration, when fitted with a red glass prismatic lens. Without side number plate illumination in indicator configuration, when fitted with an amber glass lens. Screw on metal rim. 45mm diameter x 93mm overall, body 42mm diameter. BA15D double contact equal pin bulb holder. Mounts through a 20mm panel hole. Offered in black or nickel or chrome plated finish. For spare stop and tail bulbs please see B381 (12V) and B383 (6V), or LED equivalents designed for these lamps CSTLEDWWR-6 and CSTLEDWWR-12. For spare indicator bulbs please see our B319 (6v) or B335 (12V). -- Without number plate side lens.

Early pattern cylindrical rear lamp equivalent to Lucas type 582. With side number plate illumination in stop and tail lamp configuration, when fitted with a red glass prismatic lens. Without side number plate illumination in indicator configuration, when fitted with an amber glass lens. Screw on metal rim. 45mm diameter x 93mm overall, body 42mm diameter. BA15D double contact equal pin bulb holder. Mounts through a 20mm panel hole. Offered in black or nickel or chrome plated finish. For spare stop and tail bulbs please see B381 (12V) and B383 (6V), or LED equivalents designed for these lamps CSTLEDWWR-6 and CSTLEDWWR-12. For spare indicator bulbs please see our B319 (6v) or B335 (12V). -- Early pattern cylindrical indicator lamp , as Lucas type 582. fitted with amber prismatic lens and screw on metal rim. 45mm dia x 93mm overall, body 42mm dia. - double contact equal pin bulbholder. mounts through 20mm panel hole. offered in black. Accepts BA15d indicator bulb, for spare bulbs please see our B319 (6v) or B335 (12V).

Indicator lamp of vintage appearance, modelled as the equivalent of the Lucas rear lamp type 582. Amber plastic lens 55mm dia, body 58mm long x 42mm diameter, overall length 92mm. Nickel body. We have commissioned production of this lamp to enable older vehicles to comply to more modern traffic conditions, with a larger plastic lens on a period looking flashing indicator lamp. Accepts BA15D indicator bulb, for spare bulbs please see our B319 (6v) or B335 (12V).

A neat rubber side bolt mounted indicator lamp, moulded to match the original Rubbolite 25 lamp, without any side lens (for number plate illumination). Supplied with a domed amber lens as standard (red as an option). Dimensions 63mm wide x 78mm deep - excluding bulb holder. BA15D double contact bulb holder takes equal pin bulbs - please see B319 (6v) or B335 (12v) for indicator function, or B383 (6v) or B381 (12v) (LED options CSTLEDWWR-6 and CSTLEDWWR-12) if used as a stop and tail lamp with a red lens.

Internally modified torpedo style side lamp, reproduction of the Lucas 1130 type light. Chromium plated body approx 100mm long x 46mm diameter. Frosted glass lens with chrome rim held with screw in top. The internals of this lamp have been modified to accept two individual modern (WEDGE T10 base) bulbs which provide a clear side light and an amber flashing light, mounted by two bolts in base. Rubber mounting pad supplied. 12 volt bulbs supplied only - for spare bulbs please see our B921 and B501 We now also offer a Toby reproduction of the 1142 type side lamp originally made by Lucas, a pedestal mounted torpedo lamp that is larger than the 297/1130 type - available as a sidelamp 1142S or sidelamp/indicator 1142IND

Internally modified torpedo style sidelamp, reproduction of the Lucas 1130 type. Chromium plated on brass body approx 100mm long x 46mm diameter. Clear plastic lens held with screw in top, the internals of this lamp have been modified to accept two individual modern (WEDGE T10 base) bulbs which provide a clear side light and an amber flashing light, mounted by two bolts in base. Rubber mounting pad supplied. 12 volt bulbs supplied only - for spare bulbs please see our B921 and B501

Toby 'diver's helmet' small tail lamp. 48mm diameter mains glass bulls eye lens, 42mm diameter glass bulls eye side lenses. Overall lamp diameter about 80mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs. Fitted with riveted Toby medallion. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. These superb lamps are available in polished brass, chrome and nickel, with double contact bulbholder and plug in base. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with three amber lens for indicator use. Please specify your requirement. Requires equal pin BA15D bulbs - for spare bulbs please see our B383 (6v) or B381 (12v) for stop and tail version, B318 (6v) or B335 (12v) for indicators.

Toby 'diver's helmet' rear lamp. With three 52mm diameter glass, bulls eye lenses. Overall lamp diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs. Fitted with riveted 'Toby' medallion. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. These superb lamps are available in polished brass, chrome and nickel, with double contact bulbholder and plug in base. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with three amber lens for indicator use. Please specify your requirement. Requires equal pin BA15D bulbs - for spare bulbs please see our B383 (6v) or B381 (12v) for stop and tail version, B318 (6v) or B335 (12v) for indicators.

Toby 'diver's helmet' small tail lamp handmade by ourselves. 48mm mains lens diameter, 42mm side lens diameter and overall lamp diameter about 80mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass or bright nickel. Double contact bulb holder and plug in base. Requires equal pin BA15D bulbs - for spare bulbs, please see our B383 (6v) or B381 (12v) for stop/tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps fitted with two red and one clear glass for stop, tail and number plate light service, OR with amber lenses all round for indicator use. Please specify your requirement on order. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Toby 'diver's helmet' small tail lamp handmade by ourselves. 48mm mains lens diameter, 42mm side lens diameter and overall lamp diameter about 80mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass or bright nickel. Double contact bulb holder and plug in base. Requires equal pin BA15D bulbs - for spare bulbs, please see our B383 (6v) or B381 (12v) for stop/tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps fitted with two red and one clear glass for stop, tail and number plate light service, OR with amber lenses all round for indicator use. Please specify your requirement on order. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.

Toby 'diver's helmet' small tail lamp handmade by ourselves. 48mm mains lens diameter, 42mm side lens diameter and overall lamp diameter about 80mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass or bright nickel. Double contact bulb holder and plug in base. Requires equal pin BA15D bulbs - for spare bulbs, please see our B383 (6v) or B381 (12v) for stop/tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps fitted with two red and one clear glass for stop, tail and number plate light service, OR with amber lenses all round for indicator use. Please specify your requirement on order. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Toby 'diver's helmet' tail lamp made by ourselves. 52mm lens diameter (all) and overall diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass, bright nickel or chrome finish. Double contact equal pin BA15D bulb holder and plug in base - for spare bulbs please see our B383 (6v) or B381 (12v) for the stop and tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with amber lens all round for indicator use. Please specify the configuration you require. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.

Round rear lamp with split glass lens. Polished stainless steel, embossed DUOLAMP. 97mm diameter x 51mm deep. Two single contact bulbholders fitted through back, mounting screw hole centres 45mm. Uses BA15S bulbs - for spare bulbs please see our B317 (6v) stop/indicator, B205 (6v) side/number plate light or B382 (12v) stop/indicator B207 (12v) side/number plate light. These lamps can be upgraded with part number 211-CONV which converts the bottom bulb holder to a double contact BAY15D fitting - allowing use of a twin filament bulb behind the lower red section of the main lens, providing stop, tail and number plate light functions, leaving the upper amber section for indicator/turn signal function for red/amber lensed lamps. For red/red lensed lamps, either the tail or stop function can be doubled up with the extra filament. --

Toby 'diver's helmet' tail lamp made by ourselves. 52mm lens diameter (all) and overall diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass, bright nickel or chrome finish. Double contact equal pin BA15D bulb holder and plug in base - for spare bulbs please see our B383 (6v) or B381 (12v) for the stop and tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with amber lens all round for indicator use. Please specify the configuration you require. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Toby 'diver's helmet' tail lamp made by ourselves. 52mm lens diameter (all) and overall diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass, bright nickel or chrome finish. Double contact equal pin BA15D bulb holder and plug in base - for spare bulbs please see our B383 (6v) or B381 (12v) for the stop and tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with amber lens all round for indicator use. Please specify the configuration you require. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Toby 'diver's helmet' tail lamp made by ourselves. 52mm lens diameter (all) and overall diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass, bright nickel or chrome finish. Double contact equal pin BA15D bulb holder and plug in base - for spare bulbs please see our B383 (6v) or B381 (12v) for the stop and tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with amber lens all round for indicator use. Please specify the configuration you require. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Indicator lamp of vintage appearance, modelled as the equivalent of the Lucas rear lamp type L582. Amber plastic lens 55mm diameter, body 58mm long x 42mm diameter, overall length 92mm. Black body. We have commissioned production of this lamp to enable older vehicles comply to more modern traffic conditions, with a larger plastic lens on a period looking flashing indicator lamp. Accepts BA15D indicator bulb, for spare bulbs please see our B319 (6v) or B335 (12V).

Rubber diver's helmet lamp, similar to the Rubbolite Number 8 lamp - approx 70mm diameter body. Supplied with: Red flat main lens, one red side lens and one clear side lens for stop, tail and number plate illumination use. Amber lenses all round for indicator use. SBC BA15D double contact bulbholder fitted, enabling use of double filament bulbs. For bulbs, please see our B383 (6v) or B381 (12v) for stop, tail and number plate illumination and B318 (6v) or B335 (12v) for indicator use. --

Early pattern cylindrical rear lamp equivalent to Lucas type 582. With side number plate illumination in stop and tail lamp configuration, when fitted with a red glass prismatic lens. Without side number plate illumination in indicator configuration, when fitted with an amber glass lens. Screw on metal rim. 45mm diameter x 93mm overall, body 42mm diameter. BA15D double contact equal pin bulb holder. Mounts through a 20mm panel hole. Offered in black or nickel or chrome plated finish. For spare stop and tail bulbs please see B381 (12V) and B383 (6V), or LED equivalents designed for these lamps CSTLEDWWR-6 and CSTLEDWWR-12. For spare indicator bulbs please see our B319 (6v) or B335 (12V). --

Practical small polished stainless steel (110mm x 55mm x 28mm deep) lamp with moulded polycarbonate lens. Flush mounting back with two 4.5mm mounting studs at 77mm hole centres and a single wire connection all surrounded with a rubber seal. Very similar in design to some classic Wipac lights of the sixties, including the 210 type. 12v x 10 watt festoon bulb. Choice of clear lens for a reversing lamp, red lens for an auxiliary rear warning light and amber for indicator function. For spare bulbs please see our B1240 (6v) or B273 (12v). --

Pair of right angled brackets for L875 pedestal indicators when fitted onto an MG TD. Base dimensions are 28mm wide x 55mm (deepest point) with slotted hole 20mm x 10mm. Lamp mounting plate dimensions 24mm x 34mm with a 8mm hole. Made from stainless steel.

Early pattern cylindrical rear lamp equivalent to Lucas type 582. With side number plate illumination in stop and tail lamp configuration, when fitted with a red glass prismatic lens. Without side number plate illumination in indicator configuration, when fitted with an amber glass lens. Screw on metal rim. 45mm diameter x 93mm overall, body 42mm diameter. BA15D double contact equal pin bulb holder. Mounts through a 20mm panel hole. Offered in black or nickel or chrome plated finish. For spare stop and tail bulbs please see B381 (12V) and B383 (6V), or LED equivalents designed for these lamps CSTLEDWWR-6 and CSTLEDWWR-12. For spare indicator bulbs please see our B319 (6v) or B335 (12V). --

Reproduction of the Lucas L563 Jaguar Mk2 and XK150 indicator light, clear lens. Uses a BA15s amber bulb 12v only, for spare bulbs please see our B343.

Black pedestal indicator lamp with full lens, lens diameter 50mm, overall lamp body dimensions 50mm diameter x 70mm deep. Stem 50mm long (15mm long plain section (15mm diameter) plus 35mm threaded section). M8 thread. Uses an SCC BA15S bulb. For bulbs please see our B317 (6v) or B382 (12v).

Chrome pedestal indicator lamp with full lens, lens diameter 50mm, overall lamp body dimensions 50mm diameter x 70mm deep. Stem 72mm long (50mm plain section - 15mm diameter - plus 22mm long threaded section). M8 thread. Uses an SCC BA15S bulb. For bulbs please see our B317 (6v) or B382 (12v).

Amber lensed indicator equivalent to Lucas type L794 . Alternative part number 54990. "E" Marked. Diameter 83 mm. Applications include Morgan. Uses a BA15S bulb. For bulbs please see our B317 (6v) or B382 (12v).

Indicator and front side lamp equivalent to Lucas L632 (alternative part number 52572). Applications include MGA, Morris Minor, Austin and Morris 1100, 1300 and Mini Moke. Lens diameter 80mm approx. Total diameter with chrome rim 96mm approx. Fitted with BA15S (indicator) and BA9S (side) type bulbs. For bulbs please see our B335 (12V 21W) and B989 (12V 5W).

Polished stainless steel body (110mm x 55mm x 80mm deep) with polycarbonate lens. Single bolt fixing allows choice of mounting. Ball joint mounting with spring washer and fixing nut. H3 halogen bulb 12v x 20 watt - part number B446 (H3-20-12V). Upgrade with  LED lamp H3LED-P65 if required. Choice of - clear lens for a reversing lamp, red lens for an auxillary rear warning lamp and amber lens for indicator. -- Polished stainless steel (110mm x 55mm x 80mm deep) with amber polycarbonate lens. Single bolt fixing allows choice of mounting. H3 halogen bulb 12v x 20watt - part number B446. A great value lamp and very popular.

Clear lens indicator conversion kit for Lucas type L794 lamps. Includes new clear lens, amber bulb and new bolts. Update the look of your Morgan with these high quality lenses. Supplied with a 12V SCC BA15S amber bulb - please see our part number B343B for spares.

Chrome pedestal indicator lamp as Lucas type L874. Lens diameter 65mm x 35mm deep, overall lamp body depth 92mm tapering at the back to 30mm. Stem 120mm long (10mm diameter 100m long plain section plus 20mm long M8 threaded section). Uses an SCC BA15S bulb. For spares bulbs please see our B317 (6v) or B382 (12v).

Recessed lamp with rubber boot and body. Approximately 74mm diameter. Chrome rim with amber glass lens (25mm depth from mounting panel). Lucas model L488 with flat lens. Mounts through 35mm panel hole. Supplied with a BAY15D bulb holder - for use as an indicator, just wire one connection. For bulbs, please see our B384 (6v) or B380 (12v).

Toby 'diver's helmet' tail lamp made by ourselves. 52mm lens diameter (all) and overall diameter about 90mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass, bright nickel or chrome finish. Double contact equal pin BA15D bulb holder and plug in base - for spare bulbs please see our B383 (6v) or B381 (12v) for the stop and tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps each fitted with either two red and one clear glass for stop, tail and number plate light service OR alternatively with amber lens all round for indicator use. Please specify the configuration you require. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Toby 'diver's helmet' small tail lamp handmade by ourselves. 48mm mains lens diameter, 42mm side lens diameter and overall lamp diameter about 80mm. Similar to the old CAV, Rotax and Lucas models. Sold in pairs, these superb lamps are available in either polished brass or bright nickel. Double contact bulb holder and plug in base. Requires equal pin BA15D bulbs - for spare bulbs, please see our B383 (6v) or B381 (12v) for stop/tail version, B318 (6v) or B335 (12v) for indicators. We offer these lamps fitted with two red and one clear glass for stop, tail and number plate light service, OR with amber lenses all round for indicator use. Please specify your requirement on order. Fitted with brass, chrome or nickel on brass riveted 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. --

Internally modified torpedo style side/wing lamp. Reproduction of the streamline Lucas 1130 type. Chromium plated brass body approx 100mm long x 46mm diameter. Frosted glass lens with chrome rim retained by screw in top. Mounted by two bolts in base. Rubber mounting pad supplied. Fitted with Toby 'Red dot' tell tale insert, as applied to our finest early lamp and mirror recreations. Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell's high-quality 'Toby' branded product range. The internals of this lamp have been modified to accept two individual capless bulbs with the WEDGE T10 base - a clear 5W side lamp and an amber 21W indicator lamp. 12 Volt incandescent bulbs available only. For spare bulbs please see our B921 and B501, or new LED equivalents. We now also offer a Toby reproduction of the 1142 type side lamp originally made by Lucas, a pedestal mounted torpedo lamp that is larger than the 297/1130 type - available as a sidelamp 1142S or sidelamp/indicator 1142IND

Rubber body with boot and formed metal mounting bracket with two mounting holes. An ideal lamp for hiding on older cars. With amber lens for Indicator service. 48mm Diameter. Uses a BA15S bulb, for spare bulbs please see our B317 (6v) or B382 (12v).

Lucas model SF80 semaphore trafficator, the arm extends 7 1/4" (184mm) from the pivot point. Staybright cover, 12 volts only. NOS - New old unused Lucas stock This is the SE100 unit, which is an SF80 Trafficator unit mounted in the external black painted case. So can be used externally, or removed from the casing and fitted flush into the vehicle's original coachwork. Our self-flashing LED upgrade is highly recommended. 12-volt or 6-volt

Amber lensed indicator equivalent to Lucas L539 with single contact bulb holder. Diameter 83mm. Applications include Alvis, Austin, Bentley, Bristol, Cobra, MG, Riley, Rolls Royce, Rover and Vauxhall. Uses an SCC BA15S base bulb. For bulbs please see our B317 (6v) or B382 (12v). Lamps sold individually.

Amber lensed indicator equivalent to Lucas type L691/2 . Alternative part number 52751. "E" Marked. Diameter 83 mm. Applications include Austin Healey, Hillman Imp, AC Cobra, Morgan. Uses a BA15S bulb. For spares bulbs please see our B317 (6v) or B382 (12v).

Clear lensed indicator with amber bulb. Equivalent to Lucas type L691. Alternaive part number 52649.  "E" Marked. Diameter 83 mm. Applications include - Austin Healey, Hillman Imp, AC Cobra, Morgan. Uses a BA15S amber bulb - 12v only. For bulbs please see our B343.

Internally modified torpedo-style side/wing lamp. Reproduction of the streamlined Lucas 1130-type. Chromium-plated brass body approx 100mm long x 46mm diameter. Frosted glass lens with chrome rim retained by a screw in the top and mounted by two bolts in the base. Rubber mounting pad supplied. Fitted with chrome on brass 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell's high-quality 'Toby' branded product range. The internals of this lamp have been modified to accept two individual capless bulbs with the WEDGE T10 base - a clear 5W side lamp and an amber 21W flashing lamp. 12 Volt incandescent bulbs available only. For spare bulbs please see our B921 and B501, or new LED equivalents. We now also offer a Toby reproduction of the 1142 type side lamp originally made by Lucas, a pedestal mounted torpedo lamp that is larger than the 297/1130 type - available as a sidelamp 1142S or sidelamp/indicator 1142IND

Clear lensed side lamp or indicator for 5W side or 21W amber bulb equivalent to the Lucas L539 type. Single contact bulb holder. Diameter 83mm. Applications include Alvis, Austin, Bentley, Bristol, Cobra, MG, Riley, Rolls Royce, Rover, Vauxhall and Wolseley. Uses a SCC/BA15S/1156 base bulb. Please select side light (6 or 12V) or indicator (12V only). For spare bulbs please see our B205 (5W, 6V), B207 (5W, 12V) or B343 (12V 21W amber).

Rear 'D' lamp, equivalent to the original Lucas ST51 type lamp, though converted for combined stop, tail, number plate illumination and indicator/turn signal function. 12V only with incandescent bulbs - though there are LED options that operate with 6 or 12V - please see information below regarding B117LEDWW-A (number plate), B921LEDW-A (indicator) and B383LEDWW or B381LEDWW (6 and 12v stop and tail). Body 87mm wide x 75mm tall x 54mm deep, backing base plate 95mm wide x 84mm tall.  These high quality reproduction lamps feature a steel body and back plate with a new moulded split RED and AMBER main plastic lens, plus CLEAR side lens. Two single contact WEDGE T10 capless bulb holders - for Number Plate illumination and Indicator function - and one BA15D holder for 'Stop' and Tail function. We offer this lamp in a choice of black paint or chrome plated finish, both with side number plate illumination window. Supplied complete with 2 x capless T10 base bulbs - 1 x 5w number plate illumination light and 1 x 21W indicator - and 1 x BA15D 21/5w 'stop' and tail. For spare 12V bulbs - please see B501 for number plate, B921 (B921-12V) for indicator and B3212A (B3212-equal) for stop and tail. For LED upgrade bulbs please see 'Related Products' below - part numbers B117LEDW-A, B921LEDW-A and B381LEDW which will work with 6, 12 and 24V systems, noting you may need an LED flasher unit e.g. LEDFLASH3

Toby vintage round rear lamp, equivalent to the original Lucas ST38 or 'Pork Pie' type lamp. 12V ONLY with conventional bulbs - though LED upgrade bulbs are available for 6, 12 and 24V application - please see part number CA1249LEDBK, noting that you may need an LED flasher unit e.g. LEDFLASH3. Converted for combined stop, tail, number plate illumination and indicator/turn signal function. 90mm diameter x 65mm deep. These high quality reproduction lamps feature a brass body and rim with a high quality split RED and AMBER main plastic lens plus optional CLEAR side lens. Three single contact WEDGE T10 capless bulb holders. We offer this lamp in a choice of gloss black enamel or chrome plated finish, with and without side number plate illumination window. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. Uses 3 x capless T10 base bulbs - 1 x 5w tail light, 1 x 21w stop light, 1 x 21W indicator. For spare conventional bulbs - please see B501 for tail light/number plate illumination and B921 for stop light and indicator.

Toby chrome ST38/'Pork Pie' type lamp with standard (three BA15S) bulb holder arrangement, fitted with a LED light board and split Red/Amber lens for Stop, Tail, INDICATOR Number Plate illumination operation. Suitable for 6 or 12V, Negative Earth vehicles. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination. The board is fitted with three BA15S bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection illuminates the AMBER indication/turn signal LEDs. The LED board has a very low power requirement and provides great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus a good distinction between STOP and TAIL brightness's. Fully assembled and ready to fit. Please note that the indicator function requires use of an electronic flasher unit e.g.12V LEDFLASH3 Fitted with chrome on brass 'Toby' medallion, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range.

Streamline 'Torpedo' style side/wing lamp. A quality reproduction of the Lucas 1130 type side lamp, originally available with ebony black body and plated rim. Gloss black powder coated brass body approximately 100mm long x 46mm diameter. Frosted glass lens with chrome rim retained by screw in top. Toby 'Red dot' tell tale insert in top. Mounted by two bolts in base. Rubber mounting pad supplied. The internals of this lamp have been modified to accept two individual capless bulbs with the WEDGE T10 base - a clear 5W side lamp and an amber 21W indicator lamp. 12 Volt incandescent bulbs supplied and available only. For spare bulbs please see our B921-12V and B501-12V. As an upgrade - for 6 or 12V applications - we now offer a great LED kit - part number 424ALEDBK, noting that an upgrade to an electronic flasher unit may be required - please see part number LEDFLASH3, with 6V, 12V, +ve and -ve earth versions available. Bulbs are listed as related products below. We now also offer a Toby reproduction of the 1142 type side lamp originally made by Lucas, a pedestal mounted torpedo lamp that is larger than the 297/1130 type - available as a sidelamp 1142S or sidelamp/indicator 1142IND

Streamline 'Torpedo' style side/wing lamp. A quality reproduction of the Lucas 1130 type side lamp, originally available with ebony black body and plated rim. Gloss black powder coated brass body approximately 100mm long x 46mm diameter. Frosted glass lens with chrome rim retained by screw in top. Mounted by two bolts in base. Rubber mounting pad supplied. Fitted with chrome on brass 'Toby' medallion, as applied to our finest early lamp and mirror recreations. Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell's high-quality 'Toby' branded product range. The internals of this lamp have been modified to accept two individual capless bulbs with the WEDGE T10 base - a clear 5W side lamp and an amber 21W indicator lamp. 12 Volt incandescent bulbs supplied and available only. For spare bulbs please see our B921-12V and B501-12V. As an upgrade - for 6 or 12V applications - we now offer a great LED kit - part number 424ALEDBK, noting that an upgrade to an electronic flasher unit may be required - please see part number LEDFLASH3, with 6V, 12V, +ve and -ve earth versions available. Bulbs are listed as related products below. We now also offer a Toby reproduction of the 1142 type side lamp originally made by Lucas, a pedestal mounted torpedo lamp that is larger than the 297/1130 type - available as a sidelamp 1142S or sidelamp/indicator 1142IND

Vintage 'Toby' side lamp equivalent to Lucas part number 1142. Originally fitted to many quality cars including Rolls-Royce and Bentley. All brass construction with chrome finish to lamp body, rim and plinth. Converted bulb holder arrangement to provide indicator and side lamp functionality (as our 424A bulb holder conversion for the 1130). Takes WEDGE T10 base capless bulbs - part numbers B501 and B921A (12V only), supplied. Upgrade to LED functionality with lamp kit 424ALEDBK and and electronic flasher unit LEDFLASH3. Rim and lens arrangement as original lamp. Please see our part number 1142S for original side light only version. Also part numbers 1142GLR for glass lens and rim, 1142BS for side and and 1142BSIND side/indicator bulb holder assemblies for repair or conversion of original lamp bodies. Supplied with either a 'Toby' 'tell tale' red dot or chrome on brass 'Toby' medallion - please select the option you require from the drop down box below. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. This substantial side lamp is 60mm maximum diameter and 101mm long. The plinth is 63mm long and 26mm wide. Threaded spigot 10mm diameter. Supplied complete with lock nut, moulded rubber mounting pad and wires terminating in stripped ends.

Reproduction CAV pattern Torpedo side lamps, chrome or nickel plated. Fitted with circular chrome or nickel on brass 'Toby' badge on top, as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. A knurled rim holds the clear curved bulls eye glass lens. These lamps are made to the shape of the original CAV lamp, with the body hand spun in copper to achieve the fine point of the original pattern. Approximately 71mm diameter x 137mm long. base 91mm x 31mm with 71mm mounting hole centres. Double contact bulbholder fitted. Sold in pairs only. Uses BA15D bulbs, for spare bulbs please see our B206 (6v) or B209 (12v) -- Internally modified to accept two individual bulbs which provide a clear side lamp and an amber flashing lamp, 12 volt bulbs supplied only. For spare bulbs please see our B209 side light and B288-Amber indicator.

Toby vintage round rear lamp, equivalent to the original Lucas ST38 or 'Pork Pie' type lamp. 12V ONLY with conventional bulbs - though LED upgrade bulbs are available for 6, 12 and 24V application - please see part number CA1249LEDBK, noting that you may need an LED flasher unit e.g. LEDFLASH3. Converted for combined stop, tail, number plate illumination and indicator/turn signal function. 90mm diameter x 65mm deep. These high quality reproduction lamps feature a brass body and rim with a high quality split RED and AMBER main plastic lens plus optional CLEAR side lens. Three single contact WEDGE T10 capless bulb holders. We offer this lamp in a choice of gloss black enamel or chrome plated finish, with and without side number plate illumination window. Fitted with chrome on brass 'Toby' medallion as applied to our finest early lamp and mirror recreations. 'Toby Mitchell - London NW1' is the mark Vintage Supplies has applied to its authentic reproductions of selected early CAV and Lucas pattern lamps and mirrors for over 30 years, continuing the manufacture and development of John Mitchell high quality 'Toby' branded product range. Uses 3 x capless T10 base bulbs - 1 x 5w tail light, 1 x 21w stop light, 1 x 21W indicator. For spare conventional bulbs - please see B501 for tail light/number plate illumination and B921 for stop light and indicator. --

Round rear lamp with split glass lens. Polished stainless steel, embossed DUOLAMP. 97mm diameter x 51mm deep. Two single contact bulbholders fitted through back, mounting screw hole centres 45mm. Uses BA15S bulbs - for spare bulbs please see our B317 (6v) stop/indicator, B205 (6v) side/number plate light or B382 (12v) stop/indicator B207 (12v) side/number plate light. These lamps can be upgraded with part number 211-CONV which converts the bottom bulb holder to a double contact BAY15D fitting - allowing use of a twin filament bulb behind the lower red section of the main lens, providing stop, tail and number plate light functions, leaving the upper amber section for indicator/turn signal function for red/amber lensed lamps. For red/red lensed lamps, either the tail or stop function can be doubled up with the extra filament. --

Early pattern cylindrical rear lamp equivalent to Lucas type 582. With side number plate illumination in stop and tail lamp configuration, when fitted with a red glass prismatic lens. Without side number plate illumination in indicator configuration, when fitted with an amber glass lens. Screw on metal rim. 45mm diameter x 93mm overall, body 42mm diameter. BA15D double contact equal pin bulb holder. Mounts through a 20mm panel hole. Offered in black or nickel or chrome plated finish. For spare stop and tail bulbs please see B381 (12V) and B383 (6V), or LED equivalents designed for these lamps CSTLEDWWR-6 and CSTLEDWWR-12. For spare indicator bulbs please see our B319 (6v) or B335 (12V). -- Without number plate side lens.