High quality reproduction horn equivalent to the original Lucas 'Altette' type, with chrome rim on L-shaped bracket with a 10mm mounting hole. 12 volt. Applications include MG TC etc. Stamped 'Altette'.

Small 12 volt electric horn with black body. Approximately 100mm diameter and 55mm deep. Single hole fixing bracket with 8.3mm hole. Two 6.3mm slade/Lucar type connections

Flat mounting bracket for use with part number ALT-12. Equivalent to Lucas part number 701639. 90mm total bracket length with two 7.5mm diameter fixing holes, 25mm between centres. Black powder coated steel. 

Flat mounting bracket for use with part number ALT-12. Equivalent to Lucas part number 700168. 125mm total bracket length with 11.25mm diameter fixing hole. Black powder coated steel. 

Lucas 'Altette' horn with chrome rim. A high quality reproduction from Lucas Classic of the of the original Lucas HF1234B horn. 12 volt. Many applications include MG TA, TB & TC etc. For flat mounting brackets designed to fit the mounting studs on the back of this horn please see part numbers ALTB1 (one mounting hole on tab) and ALTB2 (two mounting holes on tab). For an Altette horn pre-fitted with a curved mounting bracket, please see part number ALT-12BL. 115mm maximum rim diameter, 69mm diameter black front centre section. Rim fitted with 6 coned, hexagonal chrome nuts 11mm deep and 9.5mm across flats. Domed hexagonal centre nut, 15mm deep, 18mm across flats. 77mm max horn depth. Two brass electrical terminal connections with slotted screws on rear. Two threaded studs at 102mm centres for mounting bracket, complete with nuts. 

12V windtone horns with high and low notes. Black plastic body with chrome grilles and covers. 90 mm diameter body. Supplied with mounting brackets, screws, nuts, relay and instructions. E marked. Made in Italy.

High quality 12V horn made by Klaxon in France. Gloss black finish. KW9 model (CH5070105, 722367). 92mm body diameter, 67mm total depth including front central spigot and rear mounting bolt. Fitted with twisted metal mounting strap finishing with an M8 bolt 75mm from horn centre - bolting upwards to position horn face 30 degrees back from vertical. Supplied complete with mating female connector for ease of wiring

High quality 12 volt all black disc horn. 75mm diameter with mounting bracket and 8mm clearance hole.This horn has two terminals so the body of the horn is insulated, making it suitable for 12 volt positive or negative earth systems. High note. A top quality “E” marked horn

6 Volt Horn - black with chrome ring, attached by 6 screws, 105mm diameter, 12 volt, 2 x 6.3mm spade terminals, ‘E’ marked. Complete with mounting bracket drilled with 8.5mm mounting hole

12 Volt Horn - black with chrome ring attached by 6 screws, 105mm diameter, 12 volt, 2 x 6.3mm spade/Lucar terminals, ‘E’ marked. Complete with mounting bracket drilled with 8.5mm mounting hole

Klaxon horn. The wonderful traditional sound of a Klaxon OOOOO-HA. Red trumpet. Very loud at 110db. Universal 12V application

Mixo horns - pair. 12V High and Low tone horns. Super quality made by Klaxon in France.

Pair of Windtone horns giving high and low notes. This type of horn set was fitted to many British cars of the 1940s and 1950s, and provides a robust but musical ''hoot''. A quality reproduction of the original Lucas WT618, under bonnet model of the wind tone horn. Compact, lightweight with a black finish. We recommend using a relay as the pair requires approximately 16amps at 12v in operation. The high and low notes differ by an interval of a major third. The WT614 was the earlier model superseded by the WT618. The two models were externally almost identical, the later model having some internal wiring improvements, notably to the contact breaker and terminal block. There were also changes to the horn diaphram which made the WT618 louder than the original model. Some budget cars were originally supplied with just the "low" horn, with the "high" horn being an optional upgrade! Sold as a matched pair of high and low notes (marked H & L inside the trumpet flares).

A quality reproduction of Lucas 9H Windtone Horn, this one being the High Tone version. As used on many British cars and motorcycles from 1964 onwards. The matching Low Tone version is also available. Twin spade type terminals to connect the wiring. This is a 12 volt horn.

A quality reproduction of Lucas 9H Windtone Horn, this one being the Low Tone version. As used on many British cars and motorcycles from 1964 onwards. The matching High Tone version is also available. Twin spade type terminals to connect the wiring. This is a 12 volt horn.

Klaxon horn. The wonderful traditional sound of a Klaxon OOOOO-HA. Black trumpet. Very loud at 110db. Universal 12V application. These are by far the best quality klaxons on the market in both product quality and sound produced.

A modern variation of the traditional 'bull horn', making plenty of noise (115db). The robust electric 12 volt, 8amp horn is operated by a control lever in the cockpit. This is quite a large unit measuring some 200mm tall x 135mm wide x 185mm deep including the substantial mounting bracket.

A quality reproduction single twist motor bugle horn used on a number of early cars and motorcycles. Approximately 16" long overall, supplied with rubber horn bulb and gauze over front grill opening. We offer this item in polished brass only.

Reproduction bell fronted, curved brass horn for vintage cars and bicycles. 8" turn diameter. 2 3/4" bell diameter, 15" overall length ingluding horn bulb. 4" horn bulb diameter. 2 1/2" long, 11/16" diameter parallel section in front of horn bulb for bracket fitting. We offer this item in polished brass only.

Reproduction bell fronted, straight brass horn. Very similiar to the Lucas No.40, Desmo No.13 and Stadium No.112D motorcycle horns. 4" diameter horn bulb. 14" overall length. 2" long, 11/16" diameter parallel section in front of horn bulb for bracket fitting. We offer this item in polished brass only.

Large snake or serpent headed horn/trumpet. Overall length of this reproduction Boa Constrictor horn is approx 1750mm. The serpent head is pressed (rather than a casting), has glass eyes and forked tongue. The tapered flexible tube ends with the rubber horn bulb supplied. The lost wax cast brass mounting brackets at either end allow fixing. Original examples of this horn are now extremely rare, and we are pleased to be able to offer this well made reproduction item. We offer this horn in polished brass or nickel. -- Nickel finish

High quality, British made, tapered brass flexible horn tube for repair of Boa Horns. 1500mm long. Inside diameters - 59mm large end for solder connection to Boa head, 16.5mm small end for solder connection to horn bulb tube. Wall thickness approx 2.5mm.

Reproduction of the Lucas No.38 double twist motor bugle horn. Approx 500mm long overall, supplied with rubber horn bulb, mounting bracket and gauze over front opening. Very similar to many variations used in the 1920's period. Fitted with mounting flange. We offer this item in polished brass only.

Large and noisy 12 volt electric horn. Approximately 150mm diameter x 90mm deep (front to back). Chrome grill, mounting arm supplied.

Small 12 volt electric horn with chrome grill. Approximately 100mm diameter and 55mm deep. Single hole fixing bracket

Small 6 volt electric horn with chrome grill. Approximately 100mm diameter and 55mm deep. Single hole fixing bracket.

Warning buzzer 12 volt. Another reminder for indicators!

Klaxon horn. The wonderful traditional sound of a Klaxon OOOOO-HA. Chrome trumpet. Very loud at 110db. Universal 12V application. These are by far the best quality klaxons on the market in both product quality and sound produced.  

Large snake or serpent headed horn/trumpet. Overall length of this reproduction Boa Constrictor horn is approx 1750mm. The serpent head is pressed (rather than a casting), has glass eyes and forked tongue. The tapered flexible tube ends with the rubber horn bulb supplied. The lost wax cast brass mounting brackets at either end allow fixing. Original examples of this horn are now extremely rare, and we are pleased to be able to offer this well made reproduction item. We offer this horn in polished brass or nickel. -- Polished brass finish