Large four colour enamel badge, for the tops of some larger Lucas lamps, 19.3mm wide x 22.5mm tall. Nickel plated.

Large, four colour enamel badge, for the tops of some larger Lucas lamps, 19.3mm wide x 22.5mm tall. Chrome plated.

Original pattern frosted and ribbed lens with chrome on brass rim for our 1142S and 1142IND lamps, equivalent to the original Lucas 1142 type side lamp. Overall outside diameter 57mm, 18mm deep.

Knurled and slotted headlamp rim screw for Lucas L140, L150 etc. type headlamps. Overall length 33mm (head 9mm, thread length 24mm), head diameter 10mm. 2BA thread. Chrome plated brass. Offered as a lower cost alternative the 641 Daisy head screw.

High quality plastic split RED/AMBER lens as used inour CA1149 part number lamps - split lens 'D' lamps (part numbers 249A and 428A), equivalent to the Lucas type ST51, converted to Stop, Tail, Number Plate light and Indicator functionality.

Polished stainless steel lens retainer trim ring for the L488 and L594 indicator, side and stop/tail type lamps. 68mm outside diameter x 54mm inside diameter x 8mm tall.

Hiqh quality clamp for tightening the bulb holder socket in the back of Lucas lamp refectors onto BA15 bulb holders (e.g. our part numbers 853 or 153). The clip strap is formed from steel and nickel plated. The screw is machined brass, with a plain lead in and knurled, slotted head, also nickel plated.

Wiring harness for H4 headlamps fitted with push fit WEDGE T10 side light bulb holder that accepts capless T10 base bulbs (e.g. B501). Supplied with plastic sheathing and rubber grommet for feed through hole. BS specified wiring and wire colours. Approximate length 60cm.

7" sealed beam headlamp unit 12v 65/55watt, RHD, with side light window, three spade terminal connection. LHD unit also available.

7" sealed beam headlamp unit 12v 65/55watt, LHD, with side light window, three spade terminal connection. RHD unit also available.

PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights fitted with FULL RED lenses to bright LED operation. On board electronics make this product suitable for 6V &12V vehicles, either Positive or Negative earth. This is a new product specially designed to fit the Lucas ST51 lamp and modern reproductions to the original pattern such as Vintage Supplies'/sVc's '249 and 428' part number lamps. The product features a main, D shaped RED light board that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one BAY15D bulb base connector (15mm diameter, double contact cap with vertically offset pins) on 15cm connecting wires. One contact of the double contact holder illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second contact illuminates the Stop light (second brightness RED). Use of a bulb base style connector allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 36 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - as well as good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connector, locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps.

A PAIR of LED light boards for conversion of Lucas ST38 'Pork Pie' type lamps fitted with all RED lenses to bright LED operation. On board electronics make this product suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST38 lamp and modern reproductions to the original pattern such as '776' part numbered products. Each board features a main, circular RED light panel with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination - though the assembly is suitable for lamps with or without a number plate illumination window. The board is fitted with two BA15S bulb base connectors on 9cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The other connection illuminates the Stop light (second brightness RED). Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 36 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the bulb connectors, locating the slot in the LED board over the bulb holder partition and reassembly of the lamp. Two 3mm thick foam lens seals are provided in the kit, incase they are needed for cushioning. Conversion kit for a PAIR of lamps.

PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps.

PAIR of all in one LED light boards and split Red/Amber lenses for conversion of Lucas ST51 SPLIT lens 'D Lamp' type Stop & Tail lamps (with or without number plate illumination) fitted with all RED lenses, to Stop, Tail, INDICATOR & number plate illumination operation. On board electronics make this product suitable for 6V & 12V vehicles, either Positive or Negative earth. This is a new product specially designed to fit the Lucas ST51 lamp and modern reproductions to the original pattern, such as Vinate Supplies'/sVc's '249A' and '428A' part numbered products. The product features a main, D shaped light board with two sections of LEDs - one RED and one AMBER - that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. The board is fitted with one bulb base BA15D connector (please note - equal NOT offset pin) on 15cm connecting wires and one BA15S bulb base connector on 10cm connecting wires. One terminal of the BA15D base illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second terminal illuminates the Stop light (second brightness RED). The BA15S connection iluminates the AMBER indication/turn signal LEDs. Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 27 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the two bulb connectors and locating the LED board between the lens and the lens retaining spring clip, then reassembly of the lamps with the new Red/Amber lenses instead of the all Red split lens. Two 1.5mm thick rubber lens seals are provided in the kit, one for each lens if required. Conversion kit for a PAIR of lamps.

A PAIR of all in one LED light boards and split Red/Amber lenses for conversion of Lucas ST38 'Pork Pie' type Stop & Tail lamps (with or without number plate illumination) with all RED lenses to Stop, Tail, INDICATOR & Number Plate illumination operation. On board electronics make this product suitable for 6V & 12V vehicles, and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST38 lamp and modern reproductions to the original pattern, such as '776' part numbered products. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple bulb holder bolted into the ST38 body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination - though the assembly can be used in lamps with or without a number plate illumination window. The board is fitted with three BA15S bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection illuminates the AMBER indication/turn signal LEDs. Use of bulb base style connectors allows easy return of the lamp to its original condition if required. These boards have a very low power requirement and provide great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the three bulb connectors, locating the slot in the LED board over the original bulb holder partition and reassembly of the lamps with the new Red/Amber lenses instead of the all Red lenses. Four 3mm thick foam lens seals are provided in the kit, one for either side of each lens if required. Conversion kit for a PAIR of lamps.

PAIR of all in one LED light boards to upgrade CA1249 lamps - Lucas type ST38 'Pork Pie' Stop & Tail lamps converted to include indicator functionality with split WEDGE T10 bulb holders and split RED/AMBER lenses. On board electronics make this product suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit Lucas ST38 lamps (and modern reproductions to the original pattern) that have already been converted to include indicator functionality - Vintage Supplies' or sVc's 'CA1249' part numbered product range. The product features a main, circular RED and AMBER light board with a centre slot that fits over/locates on the vertical partition of the triple WEDGE T10 bulb holder retro bolted into the ST38 lamp body. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination. The board is fitted with three WEDGE T10 bulb base connectors on 10cm connecting wires. One connection illuminates the Tail light (first brightness RED) and the Number Plate light (WHITE). The second connection illuminates the Stop light (second brightness RED). The third connection iluminates the AMBER indication/turn signal LEDs. Use of T10 bulb base style connectors allows easy return of the lamp to its original condition and capless bulb operation if required. These boards have a very low power requirement and provide great all over lens lighting from 30 RED LEDs and 24 AMBER LEDs, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no attachment other than plugging in the three T10 bulb connectors, locating the slot in the LED board over the partition and reassembly of the lamp. Two 3mm thick foam lens seals are provided in the kit, incase they are needed for cushioning. Conversion kit for a PAIR of lamps.

PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps. --

PAIR of LED light boards for conversion of Lucas ST51 'D Lamp' type lights, fitted with SPLIT RED lenses, to bright LED operation. On board electronics make this suitable for 6V & 12V vehicles and Positive & Negative earth systems. This is a new product specially designed to fit the Lucas ST51 split lens lamp and modern reproductions to the original pattern such as Vintage Supllies'/sVc's '249A and 428A' part number products. The panel features a main, D shaped RED light board with two sections of LEDs, that locates between the original lens and the lens retaining wire. An additional WHITE LED light board is attached perpendicular to the main board to provide number plate illumination, though the assembly is suitable for D lamps with or without a number plate illumination window. Two versions of this board are available to deal with different designs of 'D lamp': Two BA15S bulb holder connectors (15mm diameter, single contact cap with equal pins) on 15cm connecting wires. One connector illuminates the Tail light (first brightness RED on both section of LEDs) plus the Number Plate light (WHITE). The second connector illuminates the Stop light (second brightness RED on both sections of LED) One BA15S single contact holder and one BA15D double contact equal pin holder - The BA15S connector illuminates the Tail light (first brightness RED on both sections of LEDs) plus the Number Plate light (WHITE). Either terminal on the BA15D connector illuminates the Stop light (second brightness RED on both sections of LED) Please check the bulb holders in your ST51 D Lamp and see whether it has two single contact bulb holders or one single and one double (BA15D) holder - then select either the BA15S/BA15S or BA15S/BA15D panel These boards have a very low power requirement and provide great all over lens lighting from 51 RED LEDS, with the fast response time/illumination under braking characteristic of LEDs - plus good distinction between STOP and TAIL red light brightnesses. This is a 'plug and play' product that requires no other attachment other than plugging in the bulb connectors and locating the LED board between the lens and the lens retaining spring clip and reassembly of the lamp. Two 1.5mm thick rubber lens seals are provided in the kit, in case they are needed. Conversion kit for a PAIR of lamps. --

'Red dot' tell tale medallion for Lucas type 1130, LD109 etc side lamps. Overall dimensions 14mm diameter x 6.25mm deep. To fit 11.5mm hole.

Reproduction frosted plastic lens for Lucas LD109 type side lamps. Will fit original lamps as well as our 918-R, 918-RB and 918-T part numbered reproduction lamps.

Chrome on brass rim fixing nut with 2BA thread. 10mm depth of female thread. Supplied with 2BA x 3/4" slotted cheese head stainless steel screw, to pull lamp body and rims togther through a bracket.

3mm thick polyeurethane foam LENS gasket for our part number series 776 and CA1249 (Lucas ST38 or 'Pork Pie' type) rear lamps. With semi-circular cut out for rim retaining screw. Often two are used per lamp to seal the lens in position.

1.5mm thick nitrile 70 shore rubber LENS gasket for Lucas ST51 'D' type rear lamps (our part number series, 428, 249 and CA1149). Suitable for solid or split lens type lamps. 

Replacement red plastic lens for our 993 flush mounted lamps, 54mm diameter with 60mm diameter flange x 44mm deep.

Replacement clear plastic lens for our 993 flush mounted lamps, 54mm diameter with 60mm diameter flange x 44mm deep.

Replacement chrome rim and red lens for our 539LST stop and tail lamp, 83mm diameter x 40mm deep. 

Replacement clear lens for our 300LC & 300CA Landrover side lamp, polycarbonate clear domed lens 67mm in diameter x 37mm deep, held by two screws with 53mm centres.

Replacement red lens for our 300ST Landrover stop & tail lamp, polycarbonate red domed lens 67mm in diameter x 37mm deep, held by two screws with 53mm centres.

Dipping reflector pivot used on Lucas two piece dipping reflectors. Spring steel 'P' clip and ball bearing holds inner refector bowl and outer reflector rim togther, allowing the inner reflector to pivot on the ball when moved by the EDS dipping module/return spring. 'P' clip 12.75mm wide, 30.5mm maximum length, 7mm hole one side of clip, 2mm deep dish for ball on other side, 3.25mm wide slot and 11mm inner diameter of 'P'. 1/4" diameter chrome plated steel ball bearing. Sold EACH.

Return spring for dipping reflectors used on Lucas lamps including the L150. Extension spring. 48mm long, 6.25mm diameter with one closed loop end and one open loop end. Please check dimensions are suitable for your reflector size.

Chome plated bronze bracket for Lucas type headlamps such as the L140. Fits inside the headlamp shell rim - the tongue fits through the slot which then accepts the rim fixing screw 641 in a 2BA threaded hole, with the base of screw 641 pulling on to catch 13016-A, located in the lamp rim. Dimensions 24mm x 13mm, threaded screw tongue 15mm wide x 13.5mm tall. 

Chrome plated bronze bracket for Lucas type headlamps such as the L140. Fits through a slot in the headlamp rim, and the base of the daisy headed rim fixing screw (part number 641) locates in the split socket, with the threaded part screwing into catch 13016-B located in the lamp shell, pulling shell and rim together. Dimensions 38mm x 15mm, screw tongue 15mm wide x 9mm tall.

High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLTKIT but compatible with many other headlamp stem bolts. Chrome finish of machined part. Good weight and finish. 38mm max outer diameter, 28mm main inner cup diameter, 15.4mm inner bolt hole diameter. 14mm overall depth, 12mm recess depth.

High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLT kit but ompatible with many other headlamp stem bolts. Black half gloss powder coated finish of machined part. Good weight and finish. 38mm max outer diameter, 28mm main inner cup diameter, 15.4mm inner bolt hole diameter. 14mm overall depth, 12mm recess depth.

Headlamp glass to reflector rectangular section cork sealing strip - 4.5mm x 7mm x 750mm long

Number plate lens gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.

Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.

Number plate lens gasket for our CA1265/1266 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.

Main rim gasket for the CA1266 series single, non-symmetrical lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.

Main rim gasket for the CA1265 series single, symmetrical lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.

Stem bolt, shakeproof washer and nut used in free standing headlights such as our 5 3/4" 1267 and and 7" AS700 part number series lamps. Excudes cup mount - please see part numbers STEMBOLTCUPB and STEMBOLTCUPC for black and chrome options.

Headlamp mounting bolt for P80 and RB160 type lamps. Thread 1/2" x 26 tpi (fine thread) as original item. Measures approx 85mm long x 13mm thread diameter (thread runs for 24mm).

Headlamp EPDM rim seal for many Lucas lamps including the L140, L148, L150 and L165 and L166. The flap locates in the 3mm wide groove in the bowl rim, behind where the reflector (bead type, rather than hemispherical cut out tab type) meets the bowl, holding both the bowl and reflector together, also creating a seal onto the glass in the rim. The seal can be cut to the exact length required and superglued into a ring, for a neat finsh and ease of installation. Priced per 0.5m (50cm) though we cut the length you require off the roll. Please indicate amount required. Approximate lengths required for popular Lucas lamps (per lamp): L140/L148 - 64cm L150 - 68.5cm L166/L165 - 73cm

Chrome on brass fixing nut for reproduction 776/CA1249 part number series lamps (reproduction Lucas ST38/'Pork Pie' type lamps) with M4 fixing stud thread.

Chrome on brass fixing nut for original Lucas ST38 'Pork Pie' type lamps with 4BA thread.

Kit of two WEDGE T10 base LED bulbs for Lucas type 1130 side lamps that have been converted to SIDE LIGHT & INDICATOR operation with the 424A T10 bulb holder kit (or purchased as 297IND, 297A-IND or 297B-IND complete lamps, with the same 3 x WEDGE T10 bulb holder). Also new sidelamp 1142IND. One very bright AMBER B921ALEDW-A LED bulb and one WHITE Osram LED B117LEDWW-A. Both these high quality bulbs accept 6 and 12 input voltages, so this one kit is suitable for both 6 or 12V vehicles. A simple conversion of these popular lamps to LED operation, as an alternative to LED combination bulbs such as CSILEDWWY - with both options providing good 6V solutions in the absence of a 6V equivalent to 12V incandescent bulb B921A (T10/T15 base 21W bulb). Kit converts one lamp, please buy 2 kits to convert a pair of bulb holders/lamps.

Kit of three WEDGE T10 base bulbs for Lucas type ST38 'Pork Pie' lamps that have been converted to STOP,TAIL & INDICATOR with the ST38CONV kit (or purchased as CA1249 lamps, with the same 3 x WEDGE T10 bulb holder) Two very bright B921LEDW-A bulbs (Indicator / Brake Light) and one Osram B117LEDWW-A (Side Light). Both these high quality bulbs accept 6 and 12 input voltages, so this one kit is suitable for 6 or 12V vehicles. A simple conversion of these popular lamps to LED operation, as an alternative to LED light panel CA1249LP-RAW - with both options providing good 6V solutions in the absence of a 6V equivalent to 12V incandescent bulb B921 (T10/T15 base 21W bulb). Kit converts one lamp, please buy 2 kits to convert a pair of rear lamps.

Highly polished stainless steel lamp rim for single (equal waisted) 'Duolamp' type lamps (our part number series CA1265)

Highly polished stainless steel lamp rim for single (unequal, waisted) lens 'Duolamp' type lamps (our part number series CA1266)

Highly polished stainless steel lamp rim, for split lens red/red or red/amber 'Duolamps' (our part number series 211RR/RA)

Plastic front lens for our 297 (Lucas 1130) type sidelamps. Purchase with O-ring seal part number 361A. Fixed in position with retaining screw part number 865 - please order seperately if required. -- Clear lens

Plastic front lens for our 297 (Lucas 1130) type sidelamps. Purchase with O-ring seal part number 361A. Fixed in position with retaining screw part number 865 - please order seperately if required. -- Amber coated lens

6V Positive Earth. 12 Amber LED, 7 Red LED tail light with 4 white LED number plate light. For lamp part number 211RA-S. two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH2

Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel pin, 1157/BAY15D double contact offset pin. Pin reference is to the side locating pins on the bulb cap. Dimensions - overall length including terminals 36mm, bulb holder body 24mm long x 16.6mm diameter, plastic base 3.6mm deep x 20mm diameter at widest point. Often held in place in the bulb holder socket in Lucas reflectors with a clamp clip (our part number 644C) not supplied. -- BAY15d fitting

Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel pin, 1157/BAY15D double contact offset pin. Pin reference is to the side locating pins on the bulb cap. Dimensions - overall length including terminals 36mm, bulb holder body 24mm long x 16.6mm diameter, plastic base 3.6mm deep x 20mm diameter at widest point. Often held in place in the bulb holder socket in Lucas reflectors with a clamp clip (our part number 644C) not supplied. -- BA15d fitting

Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel pin, 1157/BAY15D double contact offset pin. Pin reference is to the side locating pins on the bulb cap. Dimensions - overall length including terminals 36mm, bulb holder body 24mm long x 16.6mm diameter, plastic base 3.6mm deep x 20mm diameter at widest point. Often held in place in the bulb holder socket in Lucas reflectors with a clamp clip (our part number 644C) not supplied. -- BA15S (1156) base fitting

Double contact headlamp converter for most many headlamps which are mounted through the rear of reflector bowl - usually held in place in the bulb holder socket on Lucas reflectors with clamp clip (our part number 644C) not supplied. Dimensions: 17mm outside diameter, 27mm long (32.5mm including terminals)

Single ended, double contact bulb holder. Dimensions thread diameter 19mm, overall length 38mm, flange 28.5mm. Accepts SBC BA15D bulb, rear nut removes to expose terminal contacts.

MCC/BA9s bulb holder, 10.4mm diameter, useful general application spare for equal pin bayonet base 9mm cap bulbs. Single contact.

Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back. -- Plug for SBC BA15D type holder, double contact, cables enter through back.

Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back. -- Plug for SCC BA15S type holder, single contact, cables enter through back.

Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.  -- Double contact holder which accepts a plug or standard SBC/BA15D bulb at either end. Threaded outside body.

Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.  -- Single contact holder which accepts a plug or standard SCC/BA15S bulb at either end. Threaded outside body

Useful bulb holder (BA15) with bracket, (60mm x 16mm) which can be bent as necessary. --

Useful bulb holder (BA15) with bracket, (60mm x 16mm) which can be bent as necessary. --

Single contact BA15s bulbholder with wire tail. Measures outside 17mm x 26mm long. Note the two barb tags to the side to hold this in place.

12V Negative Earth. LED stop & tail conversion for 211/'Duolamp' type lamps. When brakes are applied, the "STOP" script illuminates in amber with a brighter, safer light than from standard incandescent bulbs. New technology for classic and vintage cars, motorcycles, and other custom applications that maintains an original appearance. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Add plug in module part number 211RALED-PLATE for number plate light functionality. This is the LED cluster only - not a complete lamp. An alternative upgrade with 'STOP' script for 211RR, or 211RR-S if 211RALED-PLATE is added.

12V Negative Earth. All Red LED stop & tail conversion for 211/'Duolamp' type lamps. When brakes are applied, the stop LED cluster illuminates with a brighter, safer light than from standard incandescent bulbs. New technology for classic and vintage cars, motorcycles, and other custom applications that maintains an original appearance. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Add plug in module part number 211RALED-PLATE for number plate light functionality. This is the LED cluster only - not a complete lamp. Upgrades part number 211RR or 211RR-S if 211RALED-PLATE is added.

6V Positive Earth. 12 Amber LED, 7 Red LED stop/tail light with 4 white LED number plate light. To upgrade lamp part number 211RA-S. One single contact equal pin BA15S (1156/SCC) bulb base connector (indicator function) and one offset pin BAY15D (1157) connector (stop, tail/number plate functions). High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 6V positive earth version, to eliminate the possibility of too rapid LED indicator flash. You will need to upgrade the bottom bulb holder socket on your lamp to a BAY15D socket with part number 211-CONV. This exclusive product provides STOP, TAIL, INDICATOR and NUMBER PLATE ILLUMINATION functionality all in one Duolamp cluster!

12V Negative Earth. 12 Amber LED, 7 Red LED stop/tail light with 4 white LED number plate light. For upgrade of lamp part number 211RA-S. One single contact equal pin BA15S (1156/SCC) bulb base connector (indicator function) and one offset pin BAY15D (1157) connector (stop, tail/number plate light functions). High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12V negative earth version, to eliminate the possibility of too rapid LED indicator flash. You will need to upgrade the bottom bulb holder socket on your lamp to a BAY15D socket with part number 211-CONV. This exclusive product provides STOP, TAIL, INDICATOR and NUMBER PLATE ILLUMINATION functionality all in one Duolamp cluster!

12V Negative Earth. 12 Amber LED, 7 Red LED tail light with 4 white LED number plate light. For upgrade of lamp part number 211RA-S. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12v negative earth version.

6V Positive Earth. 12 Amber LED, 7 Red LED tail light. For upgrade of lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 6V positive earth version. Add plug in number plate light module 211RALED-PLATE to upgrade 211RA-S

12V Negative Earth. 12 Amber LED, 7 Red LED tail light. For upgrade of lamp part number 211RA. Two single contact equal pin BA15 bulb base connectors. High quality polycarbonate lens. Epoxy coated, fully sealed electronics. Recommend to upgrade flasher unit to item LEDFLASH3, 12v negative earth version. Add plug in number plate module 211RALED-PLATE to upgrade 211RA-S.

Quality clear glass side lens for the number plate illumination cut out on 'Duolamp' type rear lamps - see part number series lamps CA1265, CA1266 and 211R.

Top rim stainless steel retaining screw for 297 (Lucas 1130 type) sidelamp lenses - use to retain lens part numbers 681 (glass with chrome surround) and 361C/361A (clear or amber moulded plastic).

High quality plain red glass lens for part number series CA1266 'Duolamp' type stop and tail rear lamps with a plain (unequal waisted) lens.

Replacement amber lens for our 932 lamp, domed lens with cut out for retaining screw, 54mm diameter x 22mm deep

Chrome lamp rim, glass lens and retaining seal for L489 lamp

Replacement front glass lens for Raydyot pillar mounted spot lamp 570. measures 104mm diameter.

Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber diver's lamps equivalent to the Rubbolite 'Number 8' model, please select the colour you require. -- Flat amber lens

Flat red or amber front plastic lens (58mm dia x 3mm thick) for rubber diver's lamps equivalent to the Rubbolite 'Number 8' model, please select the colour you require. -- Flat red lens

Replacement plastic side lens (44mm dia x 2mm thick) for the rubber diver's type lamp equivalent to the Rubbolite 'Number 8' model - available in clear, red or amber plastic. -- Clear spare lens

Replacement plastic side lens (44mm dia x 2mm thick) for the rubber diver's type lamp equivalent to the Rubbolite 'Number 8' model - available in clear, red or amber plastic. -- Red spare lens

Replacement plastic side lens (44mm dia x 2mm thick) for the rubber diver's type lamp equivalent to the Rubbolite 'Number 8' model - available in clear, red or amber plastic. -- Amber spare lens

Domed red or amber main lens for Rubbolite '25' model lamps (our part number series 257). Base - 60mm maximum diameter. Please select the colour you require. -- Domed amber lens

Domed red or amber main lens for Rubbolite '25' model lamps (our part number series 257). Base - 60mm maximum diameter. Please select the colour you require. -- Domed red lens

Replacement acrylic red and white lens (equivalent to Lucas part number 523308) for the Lucas 288-3 rear number plate lamp/light box assembly. The chrome rim, clip, gasket and screw is our part number 177 - currently unavailable. Dimensions 95mm wide x 67mm tall.

Replacement acrylic red lens (equivalent to Lucas part number 523307) for the Lucas 288-3 rear number plate lamp/light box  assembly. For chrome rim, clip, gasket and screw please see our part 177 - currently unavailable. Dimensions 95mm wide x 67mm tall.

Stainless steel lamp housing retaining screw - 4BA thread x 16mm long. Slotted and knurled head, 8mm diameter. Used on D lamps to secure the lamp housing to the back plate.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep amber glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm. Smooth front face, rear has a multi faceted surface.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 57mm diameter with 2mm recess around the edge which is 3mm thick, total thickness 6mm. Smooth front face, rear has a multi faceted surface.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 54mm diameter with 1mm recess around the edge which is 2.2mm thick, total thickness 9.2mm. Smooth front face, rear has a multi faceted surface.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 40mm diameter with 1mm recess around the edge which is 2.1mm thick, total thickness 6.6mm. Smooth front face, rear has a multi faceted surface.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness 7.25mm. smooth front face, rear has a multi faceted surface with 15mm bulls eye at the top.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 52mm diameter with 1mm recess around the edge which is 2.8mm thick, total thickness 7.25mm. Smooth front face, rear has a multi faceted surface.

Very high quality backlight crystal glass round reflector lens, manufactured in transparent deep red glass, 85mm diameter with 2mm recess around the edge which is 3.6mm thick, total thickness 8mm. Smooth front face, rear has a multi faceted surface.

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm.

Polished stainless steel backing cover for Lucas SF80 SE100 trafficator. overall length 195mm.

Orange plastic semaphore arm lens to fit the Lucas SF80 trafficator, part of the SE100 trafficator assembly. Equivalent to Lucas part number 532026. Overall length 180mm. 

Replacement clear plastic sleeve lens for the number plate illumination window in 288 part number series (equivalent to Lucas L582 type) lamps.

Replacement large red plastic lens with brass inner threaded insert for our 288 part number series lamps, equivalent to the original Lucas 582 lamp.

Rubber lamp entry cable grommet. Approximately 13.5mm internal diameter.

Replacement bulb holder divider plate for 776/ST38/'Pork Pie' type rear lamps. Accepts 3 x BA15S bulbs. Made to the original specification.

Spare clear side lens for part number series 776 and CA1249 (equivalent to Lucas ST38) 'Pork Pie' type rear lamps.

Spare red glass lens 82mm diameter for original Lucas type ST38/'Pork Pie' rear lamps, or our 776 part numbered reproductions. The round lenses feature a cut out for the rim fixing screw. Available with vertical or horizontal flutes. -- Vertical flutes

Spare red glass lens 82mm diameter for original Lucas type ST38/'Pork Pie' rear lamps, or our 776 part numbered reproductions. The round lenses feature a cut out for the rim fixing screw. Available with vertical or horizontal flutes. -- horizontal flutes

Replacement red split glass lens for ST51 type 'D' lamps, our part numbers 249A and 428A

Replacement red glass lens for plain ST51 type 'D' lamps, overall dimensions 67 tall x 78mm wide.

Rubber lens 'O' ring seal for Lucas type 1130 (297 series) sidelamps, with the glass lens with chrome surround and rim (part number 681).

Used in Butler type lamps - stainless steel. Use with E1ADKN-13047

Butler type headlamp screw/stud and catch barrel/boss.

Stainless steel headlamp rim retaining screw, for use with E1ADKN-13050

Spring (spectacle shape) for rims that use short rim catch clip (our 863B), equivaent to Lucas part number 509191

Chromium plated rim catch, for Lucas type head lamps, short style, overall dimensions 31mm long x 27mm wide, equivalent to original Lucas part number 509936. Use with 'spectacle' wire spring clip - our part number 864.

Chrome on bronze rim catch for Lucas head lamps, long type, overall dimensions 45mm long x 26mm wide. Makes Lucas assembly part no. 532590 with compression spring - part number 864A - and a small wire pin through the pre-drilled hole in the end of the catch.

Lamp glass clips. Small 'W' wire clip for holding lenses into rims in sidelamps. Approximately 22mm long, sold as a packet of 6 pieces

Lamp glass clips. Large 'W' wire for holding glass lenses into headlamp rims, approx 54mm long side. This clip can be used for other applications but is actually made for P100 R & S type lamps.

Lamp glass clip. Large 'W' wire spring clip for holding glass lenses into headlamp rims. Approx 48mm long side with a slight curve. Useful for deep headlamp rims. Most headlamp rims use four.

Lamp glass clip. 'W' wire clip to hold the glass into a headlamp rim - approx 36mm long. Most rims about 8" diameter use four.

Daisy head headlamp rim screw for the Lucas L140 & L150 headlamps, overall length 36mm (head 18mm, thread 18mm) head diameter 15mm tapering down to 9mm, with a 2BA thread. Chrome plated brass.

Brass headlamp stud mounting nut for Lucas RB160, P100, P80 etc. type lamps. Thread 1/2" x 26 tpi. Equivalent to Lucas part number 500357

Hexagonal nut for many Lucas type sidelamps. 7/16" x 26 tpi (very fine thread) approx 11mm bore.

Hexagonal brass nut for headlamp, 5/8" x 26 tpi (fine thread). Approx 16mm bore. 10mm deep. 13/16" AF.

Lamp mounting bolt - hollow. Thread 7/16" x 26 tpi (fine thread) as original. Measures approx 36mm long x 11mm thread diameter. Supplied with hexagon nut. Used on various Lucas spot and sidelamps.

Headlamp mounting bolt and nut for Lucas P100 type lamps. Thread 1/2" x 26 tpi (fine thread) as original item. Measures approx 105mm long x 13mm thread diameter (thread runs for 28mm), head diameter 22mm with a 12.5mm square cut under the head. Supplied with brass nut.

Headlamp mounting bolt - hollow, used on many CAV type lamps. Thread 5/8" x 26 tpi (fine thread) as original item. Measures approx 50mm long x 16mm thread diameter.

Headlamp mounting bolt - hollow, used on Butler type lamps. Thread 5/8" x 26 tpi ( ine thread). Measures approx 68mm long x 16mm thread diameter.

Headlamp mounting bolt - hollow, with loose collar. Thread 5/8" x 26 tpi (fine thread) as original item. Measures approx 50mm long x 16mm thread diameter.

Headlamp mounting bolt - hollow. Thread 5/8" x 26 tpi (fine thread) as the original item. measures approx 56mm long x 16mm thread diameter.

Silver painted bronze bracket. Fits inside headlamp rim, the tongue fits through the rim slot which then accepts rim fixing screw. Dimensions 36mm x 13mm, screw tongue 17mm wide x 13mm tall with 5mm slot.

Silver painted bronze bracket. Fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw. Dimensions 36mm x 18mm, screw tongue 17mm wide x 15mm tall with 5mm slot.

Silver painted bronze bracket for some Lucas type headlamps. Fits inside headlamp shell, the tongue fits through rim slot which then accepts a rim fixing screw through a plain 5mm diameter hole, that needs to be backed with a nut. Dimensions 28mm x 13mm, threaded screw tongue 18mm wide x 13.5mm tall.

Headlamp glass to rim rubber dust gasket for 7" Lucas 700 series type lamps. Equivalent to Lucas part number 552906.

Equivalent to Jaguar part number C2881. Bolt on side light housing for our side light part number 393 (equivalent to Lucas part number L490).

Base rubber for L691 Lucas type lamps. Fits between the lamp base and the wing. Lucas part number 54572755

Smiths type lamp badge medallion. 16mm diameter across the top 15mm approx below lip, fits into a 15mm hole. Marked Smiths across the top and London at the bottom, MA in a circle in the centre, nickel plated finish.

Rubber lens 'O' ring seal for Lucas 1130 type sidelamps (297 series lamps) fitted with the plastic lens (part number 361).

Double contact bulb holder for Lucas 1130 type side lamp, accepts double contact SBC BA15D parallel pin bulbs. Please note these are made to original pattern. These bulb holders allow conversion to side light and indicator operation with dual function white/warm white and amber LED lamps - please see part numbers  CSILEDWW and CSILEDW

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm -- large size approx 25.6mm diameter, requires approx 22mm hole

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm -- approx 23mm diameter requires 20.3mm hole

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm -- approx 22mm diameter requires 19.1mm hole

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm -- approx 18.3mm diameter requires 15.6mm approx hole

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm -- approx 15.7mm diameter, requires approx 12.6mm hole.

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. --

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. -- Available in Nickel

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. --

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. --

Desmo bronze badge/medallion, 19mm in diameter with a 2mm rivet hole in the centre. Marked 'Desmo' across the top, with winged car motif in the centre and 'Birmingham' across the bottom, available in chrome or nickel plated finish. --

Lens retaining wire for 249/428 part number series (equivalent to Lucas type ST51 type) 'D' lamps

Body to base gasket for Lucas type ST51 'D' Lamps - our part number series, 428, 249 and CA1149

Headlamp bowl to body rubber gasket for all two screw adjuster 7" (700 type) lamps. Equivalent to Lucas part number 54521487.

Reproduction of the L548 type lamp surround and lenses. Includes high quality chrome plated cast frame with red and amber lenses. Commonly fitted to Aston Martin DB4, Alvis TD21, Humber Hawk, and various Rolls-Royce and Bentley vehicles. Excludes bulb holder and base arrangement - frame and lenses only.

Flat, rubber mounting pad for 297 (Lucas 1130) type sidelamps.

Rubber rear body (boot) for Lucas L488 model type lamps. Ford part reference E0A-13216.

Rubber rear body (boot) for Lucas L594 model type lamps.

Replacement rear lamp red lens for our part number 53330 lamps, equivalent to the Lucas L549 lamp.

We have designed this backing plate to reduce light loss into the boot of a Cobra, therefore increasing the light output of L542 type lamps. 

Clear side lens for number plate window for Lucas type ST51 type 'D' Lamps - our part numbers 249, 249A, 428, 428A, CA1149B and CA1149C

Replacement glass lens for 211 part number series 'Duolamp' rear lamps. All RED or split AMBER/RED options available. --

All glass red lens for 211 part number series 'Duolamp' type rear lamps. Embossed with 'STOP' script on top section.

Replacement glass lens for 211 part number series 'Duolamp' rear lamps. All RED or split AMBER/RED options available. --

Original pattern opaque glass lens with chrome rim surround for our 297 (Lucas 1130) type side lamps, overall outside diameter 47mm. Fixed in position with retaining screw part number 865 - please order seperately if required.

Replacement rubber base gasket for Lucas L471 type rear lamps

Rubber mounting pad for our 787 (Lucas 516 type) sidelamp, dimensions 50mm long, 30mm wide, 14mm tall with 12mm hole.

Glass to rim seal ring

Replacement chrome plated lamp retaining rim for Lucas L471 type rear lamps

Replacement side mounting bracket for the pillar mounted Raydyot spotlamp. approx 106mm overall, chrome on brass.

Shallow dome head lamp base repair kit. Approx. 11mm diameter across head of bolt, stem approx. 4.5mm thread x 12mm long. Polished stainless steel, supplied with hex nuts. Per packet of 12 bolt and nut/lock washer assemblies. Also suitable for fixing bonnet panels to hinge.

BRC lamp oval plate - engraved copper. Marked 'B.R.C. lenticulaire parabolique No (space for entry) Generateur ALPHA'. Measures 59mm x 26mm

Plated dish reflector to assist with light reflection in rubber divers lamp, overall diameter 55mm with 14mm hole in the centre.

Reproduction Rotax type lamp badge/medallion. Chrome plate on brass casting with lugs on rear to peen over and secure medallion in lamp body as original. We stock the following sizes, measured across outside of badge: Very small - 15.7mm Small - 18.3mm Medium - 22.0mm Medium large - 23.0mm Large - 25.6mm

Replacement reproduction front cover (face) of our manufacture for the Lucas type 312 'Owl Eye' rear lamp. These are chrome on brass with medallion fitted. We supply these with the small red lens fitted, and the large lenses can be supplied either one clear and one red OR one amber and one red, these are held into the rear housing with retaining clips shown. -- brass finish

Stainless steel cover for rear of 211R, CA1265, CA1266, 958 'Duolamp; type lamps

Replacement reproduction front cover (face) of our manufacture for the Lucas type 312 'Owl Eye' rear lamp. These are chrome on brass with medallion fitted. We supply these with the small red lens fitted, and the large lenses can be supplied either one clear and one red OR one amber and one red, these are held into the rear housing with retaining clips shown. -- Chrome finish

Deep red glass moulded lens of bulls eye pattern measures 74mm diam x 23mm deep approx. A lovely rich red/maroon colour - clear but so deep you can not actually see through it. Nice curved top face and the rear has an outer step about 3mm wide and proud by about 2mm note picture shows the front and rear views - price each

Raydyot brass lamp badge medallion, 17mm diameter across the top 15.5mm approx below lip, fits into a 15.5mm hole, marked RAYDYOT LTD in the centre with Made in England around the edge. Available in brass or chrome - please select required finish from the option box below.

Two T10 edge base bulbs (amber for flasher, clear for sidelamp) - 12 volt ONLY. Bulb holder for fitting into Lucas 1130 sidelamps (equivalent to our 297 part number series lamps). Supplied in pairs only. Mounting plate dimensions :- 64mm long x 22mm wide with fixing holes at 50mm centres. Bulb holder plinth is 36mm tall x 25mm wide. For spare bulbs please see our B921A and B501. These bulb holders can also be upgraded to LED operation with LED lamp kit 424ALEDBK. Supplied with set screws and washers.

Long daisy head head and spot lamp rim screw for some large Lucas headlamps including the P80, overall length 49mm (head 29mm, thread 20mm) head diameter 15mm tapering down to 9mm, with a 2BA thread. Chrome plated brass.

Compression spring for use with long rim catch part no. 863A. The spring is held in place by a small roll pin inserted through the end of the catch). Makes Lucas part no assembly 532590

White LED number plate lens/LED light cluster module that plugs in to 211/'Duolamp' LED light clusters - 211RALED-STOP, 211RALED-RED, 211RALED and 211RA6LED, all pre-fitted with a wired tail/male connection that sockets with the female connection on this part.

Desmo bronze badge/medallion, 19mm in diameter with a 2mm rivet hole in the centre. Marked 'Desmo' across the top, with winged car motif in the centre and 'Birmingham' across the bottom, available in chrome or nickel plated finish.

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. --

Reproduction 'King of the Road' Lucas type lamp medallion. Chrome plated brass pressing with lugs on rear to peen over and secure the medallion on the lamp body as original. We stock the following sizes (measure overall diameter of badge). Reference A - Very small, 15.1mm Reference AC - Very small, curved (for fitting to 1130 lamp bodies), 15.1mm. Reference B - Small, 16.8mm. Reference C - Medium small, 19.7mm. Reference D - Medium, 22.7mm. Reference E - Large, 28.8mm. -- Curved in the correct direction for fitting to an 1130 type torpedo side lamp

Desmo bronze badge/medallion, 19mm in diameter with a 2mm rivet hole in the centre. Marked 'Desmo' across the top, with winged car motif in the centre and 'Birmingham' across the bottom, available in chrome or nickel plated finish. --